Buffer Cleaner
Oman Chemical is leading one Largest Supplier, Manufacture a
PRODUCT NAME | : | DIOCTYLPHTHALATE |
CAS number | : | 117-81-7 |
UN number | : | |
Formula | : | C6H4(COOC8H17)2 |
Odour | : | MILD |
Solubility in water | : | INSOLUBLE |
Density | : | 0.986 at 20 oC |
Boiling point | : | 386 oC |
Melting point | : | -55oC |
Viscosity | : | |
Flashpoint | : | 199oC |
Explosive limits | : | 0.3 – 2.4 Vol% |
Vapour pressure | : | -10 mbarat 20oC |
Skin absorption/irritation | : | YES |
TLV Country NL Year 1995 | : | ppm 5 mg/m3 |
Pollution category | : |
III |
RXSOL provide wide range of Chemicals such as Detergent Chemical, Agricultural Chemical, Industrial Chemical, Plastic Chemical and many more. We are serving in the industry from a long time period and offering our qualitative product to our renowned customers with the view to satisfying their need by the extreme quality product. They are highly appreciated in the market best of using best quality raw material while manufacturing.
NOTE : Acts as an acid-neutralizing agent.
LAC Liquid Alkaline Cleaner is a blend of Silicate, alkaline detergents, water conditioners, and biodegradable wetting and penetrating agents.
We are LAC Alkaleen liquid Tank Cleaners manufacturers in india. And holding no-1 position for LAC Alkaleen liquid Tank Cleaners suppliers in kandla, mundra, chennai, ennore, vizag, kakinada, jnpt, manglore, kolkata, haldia, paradip, dubai, fujairah, sharjah. Alkaleen Liquid Heavy Duty concentration makes surface clean easily and effectively.
CAS No of Ethoxy Propanol: 1569-02-4
Chemical Formula of Ethoxy Propanol: C5H12O2
Product Properties
Colour |
Clear light brown liquid |
|
|
Density |
In g/cm3 at 15°C: 0.99 |
|
|
Flash Point |
(PMCC)°C: Above 62 |
|
|
Copmtibility |
|
|
When mixed with water, a clear emulsion is formed. |
Metal |
No known effect |
|
|
Rubber |
May swell |
|
|
Sythetic Rubber |
May swell |
|
|
Packaging |
RXSOL-20-2001-210 |
(in Litres) |
Flash Point : > None |
Using-Procedure
Spraying:–
This can be beneficial as part of the initial cleaning process after the carriage of Lube oils and Lube oil additives. As soon as the tank in question has been checked empty by the attending surveyor, RXSOL-20-2001-210 should be sprayed over all surfaces which are safely reacheable.
Portable machines:–
After 45 minutes the butterworth machines should be operated for 3 x 20 minutes drops using warm 60o C, then the machines brought back to the top and a full hot wash 80 – 85 o C should be carried out for at least 6 hours.
Fixed machines:–
Wash ambient for 45 minutes followed by warm water for one cycle before increasing to hot (80oC) for 4 hours.
Injection:–
This can be carried out by injecting RXSOL-20-2001-210 into the butterworth system after the heater. A normal amount to use would be 100 – 150 liters during the initial washing cycle. Water temperature should be 60o C during the injection period then brought up to 80 – 85 o C for the full washing period.
Re-circulation:–
Possibly the best result are achieved by re-circulating a solution of RXSOL-20-2001-210 after the initial rough washing of the tank. A sufficient amount of fresh water to maintain good suction should be heated to 60 o C and approximately 420 liters of RXSOL-20-2001-210 (2 drums) added for each 500 liters of fresh water. The temperature of the mixture can be increased depending upon the melting point if the product being cleaned. The solution should be circulated for at least 4 hours and the butterworth machines operated at maximum pressure in all areas of the tank throughout this process. If a number of tanks are to be circulated, then a substantial quantity of solution can be made so that transfers can be made without delay and any small amounts lost will not affect the operation. Normally following transfer to another tank, 100 liters RXSOL-20-2001-210 is added for each 5000 liters of solution. This is called “spiking”.
Following the re-circulation process, the tank must be hot butterworthed 80-85o C for at least 6 hours.
*Use a strainer at the pumpstack when circulating any solution RXSOL-20-2001-210 is recommended for local cleaning and degreasing and may be applied by brush, hand spray, immersion, soaking or any other conventional means. Apply concentrate RXSOL-20-2001-210 over soiled area and wait for 20-30 minutes before rinsing off with water.
Soak Method:-
For heavy oil and soil Put parts to be cleaned into a bath of concentrate RXSOL-20-2001-210 and for medium to light soiling use a solution of 10-30% RXSOL-20-2001-210 in water. Parts should be soaked for at least 30 minutes before washing off with water.
Spray-Method:-
Spray concentrate RXSOL-20-2001-210 over all soiled areas. With in 15 and 30 minutes, RXSOL-20-2001-210 starts its function then rinse off by water hose. For stubborn deposits, agitation by scrubbing will assist the cleaning operation .
Cargo Tank Cleaning after Mineral Oils
Direct injection method:–
Make a solution of RXSOL-20-2001-210 between 0.1 and 2.0% i.e. one to twenty litres per ton wash water. Then use with Tank cleaning machine , Best results are obtained when water is heated to a temperature between 60 to 80°C. Slops Should be Constantly Stripped from, tank.
Recirculation method / Ship's Rocking Mottion:–
Make soln. Strength with RXSOL-20-2001-210 between 0.5 –3 % and used with Tank Cleaning machines OR fill the tank to 20-30% volume with sea water and add the RXSOL-20-2001-210 up to full dose . For better results heat the solution between 60 - 80°C.
NOTE : Dose rate and results will vary depending on amount of contamination.
Spot cleaning- RXSOL-20-2001-210 (concentrate) can be sprayed over surfaces and left for 20 - 30 minutes Finally wash down the tank surfaces with hot water between 60°C and 80°C with high pressure machine . Keep stripping tank slops and transfer to holding tank/slop tank.Cleaning of theOil side of Lube Oil Heat Exchangers Cleaning is best achieved by the recirculation method using a heated 20% solution of RXSOL-20-2001-210.
1) First of all drain off any remaining oil from Heat Exchanger.
2) Connect the discharge side of a portable pump to the lower heat exchanger connection & the suction Side of the pump to the bottom outlet of a 200 litre drum.
3) Complete the circuit by connecting the upper connection on the heat exchanger to the top of the drum.
4) Maintain the bath temperature between 60-80 0 C throughout the cleaning operation. If it is not possible to heat, the operation will need to be extended.
5) Use the pump to maintain circulation for 12 to 15 hours. When the cleaning is completed, disconnect the lower heat exchanger connection and drain out the cleaning solution.
6) Connect a fresh water supply to the upper heat exchanger connection, and rinse until the water runs clean from the lower connection. When rinsing is complete, disconnect the water supply and thoroughly drain and dry the heat exchanger
PRODUCT NAME | : | PHOSPHORIC ACID |
CAS number | : | 7664-38-2 |
UN number | : | 1805 |
Formula | : | H3PO4 |
Odour | : | Characteristic Odour |
Solubility in water | : | COMPLETE , ( 5.48 g/mL ) |
Density | : | 1.834 at deg C |
Boiling point | : | 213 deg C |
Melting point | : | 42 deg C |
Viscosity | : | 147 cP (100 %) |
Flashpoint | : | NA |
Explosive limits | : | NA |
Vapour pressure | : | 0 mbar at 20 deg C |
Skin absorption/irritation | : | YES |
TLV Country NL Year 1995 | : | ppm 1 mg/m3 |
Pollution category 1994 | : | D |
Properties :
- Molecular formula: H3PO4
- Molar mass : 98.00 g/mol
- Appearance : white solid or colourless, viscous liquid (>42 °C)
- Density : 1.885 g/mL (liquid)1.685 g/mL (85 % solution)2.030 g/mL (crystal at 25 °C)
- Acidity (pKa): 2.148, 7.198, 12.375
Pure phosphoric acid is colorless, odorless and has sour odor.
Phosphoric acid is Soluble in water and ethanol. Easily absorb moisture. Easy to be crystallized under cold condition for long time.
Phosphoric Acid is Corrosive. Should be stored in closed containers.
Suggestion ::: Our daily descaling works helps to share helpful tricks to dissolve hard scale easily, Always use 5-10 % our new generation hard scale deposit remover powder RXSOL-11-1102-025 . Addition of RXSOL-11-1102-025 helps to clean 100% scale from system .
Test Typical Value
Specific Gravity @ 15°C...………. 1.25
Approx. wt./litre…………………... 1.2 kg/l
Viscosity @ 40°C...………………. 6 cps
Form...……………………………... Liquid
Flash Point ...................................None
Water solubility .............................Complete
pH …………………………………...2
Appearance | White Powder, Granular, |
Chemical Name | Sodium Dichloroisocyanurate |
Formula | C3O3N3Cl2Na |
Chlorine | >62% |
Molecular Weight | 219.95 |
pH (1% solution) | 6.0 to 7.0 |
Moisture | 0.5 to 1.00% max |
Solubility @ 25°C | Completely soluble in water |
Density | Tap density = 0.974 g/mL |
The requirements for pool water testing in the application of dichlor based products should be indicated on the product label. The primary parameter to be tested is the level of FAC in the water. The choice of testing methods will vary depending on the type of pool (residential or commercial) and local regulations and standards. The product label should recommend that the pool water quality be properly balanced. This requires testing of the pool water balance parameters of pH, alkalinity, calcium hardness, and stabilizer (i.e. cyanuric acid).