Buffer Cleaner
Oman Chemical is leading one Largest Supplier, Manufacture a
Cement Remover based on principal of Chemically Back-Set formulation, which converts the positive ions in the hardened matrix into negative ions, which dissolves the cement into mud that can be rinsed away. Because it works chemically, rather than mechanically, Back-Set may be used to remove cured concrete, mortar, grout, and stucco from virtually any surface without harm.
The hardened concrete is saturated with Back-Set, either with a brush or by spraying. After 15-20 minutes, the area is again saturated with the chemical. The concrete typically begins to soften in 20-30 minutes, and can be rinsed off with water.
Excellent , concentrated and very effective cement remover with powerfull dissolving properties used on cement and bulk carriers.
The hardened concrete is saturated with Back-Set, either with a brush or by spraying. After 15-20 minutes, the area is again saturated with the chemical. The concrete typically begins to soften in 20-30 minutes,and can be rinsed off with water.The amount required for dosage can be obtained BY knowing the deposition composition as well as nature of cement to be removed.5 to 20 % recommended .These are recommended values based on experience. For optimum results dose RXSOL-22-2202-050 directly to the surface .
The amount required for dosage can be obtained BY knowing the deposition composition as well as nature of CEMENT to be removed . 5 to 20 % recommended .These are recommended values based on experience.
For optimum results dose RXSOL-22-2202-050 directly to the surface
Undiluted : In cases where we deal with heavy deposit build–up, CEMENT REMOVER must be applied undiluted.
Diluted : In cases of light deposition, on large surface areas, a solution between 10–40% may be used.
B. Cleaning Procedure
Undiluted/Diluted: In parts such as corner cavities, tank skeleton inlets, etc, Apply RXSOL-22-2202-050 through hard brush, mop, sponge or any other manual method. Let it soak for 15 minutes. Afterwards, wash thoroughly by applying high–pressure water source. In case of deposit persistence, repeat the cleaning procedure.
Refer to technical datasheet.
METHOD :::
1.For heavy deposition and thick layers of cement, a concentrated and stronger cleaner will be necessary to cut through the layers of cement.
2.Use a scraper, metal scrubber or flat head screwdriver to remove as much of the cement as possible.
3.For the remaining cement, apply this chemical
4.Once the cement loosens, scrub the area with a scrubber until it is all removed from the surface.
5.Rinse the area well with clean water.
6.Clean the area with alkaline soap and water
7.Flush system completely.
Other Valuable Hold Cleaners :::
Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020, Part No.- RXSOL-22-2202-050
| Appearance | Hazy liquid |
| Density | In g/ml at 15°C: 1.1 |
WHY RXSOL-22-2202 is better ?
Biodegradable & non flammable , Economical very cost effective
Non-hazardous
Non-fuming
Safe for paint, chrome, aluminum, glass, rubber, plastic, brass & stainless
Dissolves cured cement, concrete, mortar, grout, stucco
Cleans aluminum
Also comes with a foaming spray nozzle
Will not remove rubberized cement
Suitable for the removal of cement deposits and dry stains.
Due to its higher concentration its chemical reaction is very fast.
It's chemical combination meet the requirements of paragraph 1.8.2 of the P&A Standards.
We are marine chemical supplier since 1996.These Marine Chemicals include different sets of products such as Tank Cleaners, Maintenance Chemicals, Cooling Water Treatment Chemicals, Boiler Water Treatment Chemicals, Fuel Additives, etc.
Oman Chemical is leading one Largest Supplier, Manufacture a
Oman Chemical is leading one Largest Supplier, Manufacture a
