CrudeClear Defoamer DFX

Size:

Color:

Product Short Description: RXSOL-16-2066 is antifoam emulsion and its more concentrated antifoam emulsion. It has excellent candidates for controlling foam in amine and glycol dehydration units. This is suitable products for gas plants and have excellent stability in the presence
Product Technical Specification:

 

Emulsion: Silicone Antifoam Emulsion RXSOL-16-2066-210
Chemical Nature Emulsion of a silicone antifoam compound
Appearance White, homogeneous, slightly viscous liquid

Viscosity at 25°C, cSt
600
Active Ingredients, % 10
Specific Gravity at 25°/25°C 1
pH 7
Emulsion Type Non-ionic
Suitable Diluents Water only
 
Remarks:
Images: Alt



Phosphorous Acid

Size:

Color:

Product Short Description: Phosphorous acid is a chemical substance that is used to make other phosphorus compounds.Phosphorous acid appears as a white or yellow crystalline solid (melting point 70.1 deg C) or a solution of the solid. Density 1.651 g /cm3 . Contact may severely irritate skin, eyes, and mucous membranes. Toxic
Product Technical Specification:

 

Particular Result
Appearance (Color) : White to pale cream
Form : Flakes or crystals or crystalline powder or powder
Assay : ≥98.0 to ≤102.0%
Formula : H3PO3
Molecular Weight : 82
Melting point : 74°C
Density : 1.651
Boiling Point : 200° C
pH : 1.0
Remarks:

GHS Hazard and Precautionary Statements
 

Hazard Statements: H290-H302-H314

May be corrosive to metals. Harmful if swallowed. Causes severe skin burns and eye damage.

Precautionary Statements: P264b-P270-P271-P280-P304+P340-P305+P351+P338-P310-P330-P331-P363-P390-P402-P403+P233-P406b-P501c

Wash face, hands and any exposed skin thoroughly after handling Do not eat, drink or smoke when using this product. Use only outdoors or in a well-ventilated area. Wear protective gloves/protective clothing/eye protection/face protection. IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor/physician. Rinse mouth. Do NOT induce vomiting. Wash contaminated clothing before reuse. Absorb spillage to prevent material damage. Store in a dry place. Store in a well-ventilated place. Keep container tightly closed. Store in corrosive resistant polypropylene container with a resistant inliner Dispose of contents/ container to an approved waste disposal plant

Images: Alt



Sodium Lauryl Sulphate SLS

Size:

Color:

Product Short Description: Excellent decontamination, Emulsification and Foaming property. With rich and longstanding foam.
Product Technical Specification:

 

Item

Specification

95%

92%

30%

Appearance 25`c

White to yellowish powder of needle

White to yellowish powder  to needle

Colorless to yellowish transparent liquid

Odor

Characteristic odor

Characteristic  odor

Characteristic  odor

Active matter, %

95.0 min

92.0 max

30+1

Petroleum ether soluble substance, %

1.5 max.

1.5 max.

1.5 max.

Sodium sulfate, %

3.0 max.

5.0 max.

1.0 max.

pH value (25`C , 1% Am.aq.sol)

7.5-9.5

7.5.9.5

7.5.9.5

Color, Hazen (5%Am.aq.sol)

10 max.

10 max.

10 max.

Water content,%

3.0 max.

5.0 max

      /

 

 

Remarks:

Sodium Lauryl Sulfate (SLS) 95%

Appearance,25℃: White to yellowish powder or needle
Odor: Characteristic odor
Active matter, %: 95.0 min.
Petroleum ether soluble substance, %: 1.5 max.
Sodium sulfate, %: 3.0 max.
Ph value (25℃, 1% Am.aq.sol): 7.5-9.5
Color, Hazen (5% Am.aq.sol): 10 max.
Water content, %: 3.0 max.

Sodium Lauryl Sulfate (SLS ) 92%
Appearance,25℃: White to yellowish powder or needle
Odor: Characteristic odor
Active matter, %: 92.0 min.
Petroleum ether soluble substance, %: 1.5 max.
Sodium sulfate, %: 5.0 max.
Ph value (25℃, 1% Am.aq.sol): 7.5-9.5
Color, Hazen (5% Am.aq.sol): 10 max.
Water content, %: 5.0 max.

Sodium Lauryl Sulfate (SLS ) 30%
Appearance,25℃: White to yellowish powder or needle
Odor: Characteristic odor
Active matter, %: 30±1
Petroleum ether soluble substance, %: 1.5 max.
Sodium sulfate, %: 1.0 max.
Ph value (25℃, 1% Am.aq.sol): 7.5-9.5
Color, Hazen (5% Am.aq.sol): 10 max.
Water content, %: nill
Packing

Item

Packing

QuantityFCL

N.W/FCL

G.W/FCL

SLS 95 or 92%

20kgs/Bag

525 Bags

10.50MT

10.763MT

20kgs/Bag

400 Bags

8.00MT

8.200MT

SLS 30%

200Kgs/Plastic Drum

80 Drums

16.00MT

16.800MT

1000Kgs/IBC

18 IBCs

18.00MT

19.152MT

 

SLS 95% or 92%:
1) 20kg/bag, 10.5mt/fcl (N.W.),10.763mt/fcl (G.W.) without pallet
2) 20kg/bag, 8mt/fcl (N.W.),8.2mt/fcl (G.W.) with pallet SLS 30%:
1) 200kg/plastic drum, 16mt/fcl (N.W.), 16.8mt/fcl (G.W.)
2) 1000kg/IBC, 18mt/fcl (N.W.), 19.152mt/fcl (G.W.)

Storage: Stored in dry, cool and ventilated place, kept away from sunshine and rain.

Images: Alt



Ethoxy Propanol

Size:

Color:

Product Short Description: Ethoxy propanol or ethoxypropanol or ethyl ether of propylene glycol
Product Technical Specification:

CAS No of Ethoxy Propanol: 1569-02-4
Chemical Formula of Ethoxy Propanol: C5H12O2

Remarks:
Images: Alt



Alkaline Cleaner

Size:

Color:

Product Short Description: RXSOL heavy duty Alkaline Product have proven to be a highly effective agent for maintaining effective levels of cleanliness on cargo tanks and on other metal surfaces.
Product Technical Specification:
Remarks:
Images: Alt



Diesel Fuel Tank Cleaner

Size:

Color:

Product Short Description: Diesel Fuel Tank Cleaner Removes Sludge, Varnish and Other Deposits – Concentrated Formula Works In Gas Tanks, Fuel Tank & Diesel Tanks.
Product Technical Specification:

Product Properties

Colour

Clear light brown liquid   

 

 

Density

In g/cm3 at 15°C: 0.99   

 

 

Flash Point  

(PMCC)°C: Above 62   

 

 

Copmtibility

 

 

When mixed with water, a clear emulsion is formed.

Metal

No known effect

 

 

Rubber

May swell

 

 

Sythetic Rubber

May swell

 

 

Packaging

RXSOL-20-2001-210

 (in Litres)
25 ,35 ,50, 210

Flash Point : > None

  

Remarks:

Using-Procedure    

Spraying:–

This can be beneficial as part of the initial cleaning process after the carriage of Lube oils and Lube oil additives.  As soon as the tank in question has been checked empty by the attending surveyor, RXSOL-20-2001-210  should be sprayed over all surfaces which are safely reacheable.
 

Portable machines:–

After 45 minutes the butterworth machines should be operated for 3 x 20 minutes drops using warm 60o C, then the machines brought back to the top and a full hot wash 80 – 85 o C should be carried out for at least 6 hours.

Fixed machines:–

Wash ambient for 45 minutes followed by warm water for one cycle before increasing to hot (80oC) for 4 hours.

Injection:–

This can be carried out by injecting RXSOL-20-2001-210  into the butterworth system after the heater. A normal amount to use would be 100 – 150 liters during the initial washing cycle.  Water temperature should be 60o C during the injection period then brought up to 80 – 85 o C for the full washing period.

Re-circulation:–

Possibly the best result are achieved by re-circulating a solution of RXSOL-20-2001-210 after the initial rough washing of the tank.  A sufficient amount of fresh water to maintain good suction should be heated  to 60 o C and approximately 420 liters of RXSOL-20-2001-210  (2 drums) added for each 500 liters of fresh water.  The temperature of the mixture can be increased depending upon  the melting point if the product being cleaned.  The solution should be circulated for at least 4 hours and the butterworth machines  operated at maximum pressure in all areas of the tank  throughout this process.  If a number of tanks are to be circulated, then a substantial quantity of solution can be made so that transfers can be made without delay and any small amounts lost will not affect the operation.  Normally following transfer to another tank, 100 liters RXSOL-20-2001-210  is added for each 5000 liters of solution.  This is called “spiking”.
  

Following the re-circulation process, the tank must be hot butterworthed 80-85o C for at least 6 hours.
      *Use         a                 strainer                at               the                 pumpstack               when               circulating          any                        solution              RXSOL-20-2001-210 is recommended for local cleaning and degreasing and may be applied  by  brush,  hand  spray, immersion, soaking or any other conventional means. Apply concentrate RXSOL-20-2001-210 over  soiled  area  and wait for 20-30 minutes before rinsing off with water.
 

Soak Method:-

For heavy oil and soil Put parts to be cleaned into a bath of concentrate RXSOL-20-2001-210 and  for medium to light soiling use a solution of 10-30% RXSOL-20-2001-210 in water. Parts should be soaked for at least  30 minutes  before washing off with water.

Spray-Method:-

Spray concentrate  RXSOL-20-2001-210  over all soiled areas.  With in  15  and  30   minutes,  RXSOL-20-2001-210 starts   its function then rinse off by water hose. For stubborn deposits, agitation by scrubbing will  assist  the  cleaning operation .

Cargo Tank Cleaning after Mineral Oils

Direct injection method:–

Make  a   solution  of  RXSOL-20-2001-210  between   0.1  and  2.0%   i.e.   one   to    twenty    litres    per  ton   wash water.   Then      use     with     Tank     cleaning      machine ,    Best     results    are     obtained   when   water  is    heated  to  a     temperature      between          60  to  80°C.  Slops Should              be             Constantly              Stripped       from, tank.                                                   

Recirculation method / Ship's Rocking Mottion:– 

Make  soln.  Strength  with RXSOL-20-2001-210 between  0.5 –3 %  and  used  with  Tank Cleaning machines OR fill the tank to 20-30% volume with sea water and add the RXSOL-20-2001-210 up to full dose  . For better  results  heat  the solution  between 60 - 80°C.

NOTE : Dose rate and results will vary depending on amount of contamination.

Spot cleaning- RXSOL-20-2001-210  (concentrate) can be sprayed over surfaces and left  for  20 - 30 minutes  Finally wash down the tank surfaces with hot  water between 60°C and 80°C with  high  pressure   machine .   Keep stripping tank slops and transfer to holding tank/slop tank.Cleaning  of  theOil  side of  Lube  Oil Heat Exchangers  Cleaning  is  best  achieved  by the recirculation method using a heated 20% solution of RXSOL-20-2001-210.
1) First of all drain off any remaining oil from Heat Exchanger.
2) Connect the discharge side of a portable pump to the lower heat exchanger connection & the suction Side of the pump to the bottom outlet of a 200 litre drum.
3) Complete the circuit by connecting the upper connection on the heat exchanger to the top of the drum.
4) Maintain the bath temperature between 60-80 0 C throughout the cleaning operation.  If it is not possible to heat, the operation will need to be extended.
5) Use the pump to maintain circulation for 12 to 15 hours.  When the cleaning is completed, disconnect the lower heat exchanger connection and drain out the cleaning solution.
6) Connect a fresh water supply to the upper heat exchanger connection, and rinse until the water runs clean from the lower connection.                                                                                                                                                                                                                                                              When rinsing is complete, disconnect the water supply and thoroughly drain and dry the heat exchanger

Images: Alt



ECOSOLV 222 ACID FRAC TANK CLEAN

Size:

Color:

Product Short Description: Specially formulated for cleaning and fast-acting solvent cutter for tank plate etc, used for fuel oils. Also for local cleaning and degreasing of deck and engine rooms, Oil installations, workshops, plant yards, industrial plants as degreaser and cleaner
Product Technical Specification:

SEA VOYAGE CLEAN Plus is Highly effective concentrated cleaner .
Versatile, can be used for a wide application range ( for TANK or general cleaning .)
Provides quick and thorough emulsifying action.
Can be used for cleaning , gas freeing of double bottom, deep and other fuel oil bunker tanks.
May also be used for cleaning and gas-freeing of crude and refined mineral oil cargo tanks.
It can be used as a general purpose cleaner to remove oil and grease deposits  and cleaning of bilge spaces and engine rooms from soiled surfaces. Can be used for degreasing and cleaning engine cooling water systems
 

Remarks:
Images: Alt



Rig Wash Tuff Heavy Duty

Size:

Color:

Product Short Description: Heavy duty non corrosive concentrated cost effective surfactant solution used for surface cleaning applications. This cleaning compound is soluble in fresh and salt water , also suitable with high presure cleanig machines. Ideal for difficult cleaning pro
Product Technical Specification:
Remarks:

Maintenance Cleaning chemicals for RIGS and oil field industries. RIGWASH Powder is powerful degreasing and emulsifying cleaning chemicals. RXSOL BRAND is most popular brand in MARINE and Oil Field industries as RIGS and Oil Field CHEMICALS supplier. RXSOL BRAND have various grade of RIGS CLEANING Detergent which includes RIG WASH LIQUID

Rigwash is classified  cleaning  detergent for offshore oil and gas rigs, platforms, and associated equipment. RIGWASH developed such a way to use by high-pressure water jets, detergents, and degreasers to remove dirt, grease, oil, and other contaminants that may have accumulated on the surface of the rig or equipment.

Regular use of Rigwash is important for maintaining the safety and efficiency of the equipment and reducing the risk of corrosion and damage.

Images: Alt



Potassium Chloride

Size:

Color:

Product Short Description: Potassium Chloride Exporter, Manufacturer
Product Technical Specification:

Appearance                                                                     White free flowing crystalline powder

Density                                                                             1.98 SG

Bulk Density                                                                     71 to 78 Ib/ ft³

Aqueous Solubility                                                           Up to 24%, 278.9 gL of solution at 68˚F (20˚C)

Purity                                                                               98.83%-99%

K20                                                                                  62% and above

Remarks:
Product Details:
 
Color White
Grade Standard Reagent Grade, Technical Grade
Packaging Size 50kg
Packaging Type HDPE bags
Physical State Powder, Granules, Crystals
Usage Industrial
Purity 99%
Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App



Hydro Testing Oxy Scavenger Biocide

Size:

Color:

Product Short Description: Hydro-testing corrosion protection for Pipeline, Tank
Product Technical Specification:
 
Form                                         Liquid
Colour Colourless to slightly Yellow
Odour Sharp
Flash Point  > 100C
Density 1.05-1.11 g/cm3 (25C)
pH 3 - 7
 

Non-Flammable

Safe Plant Handling
Low Odor
Provides corrosion protection in the liquid and the vapor phase
When used in hydrostatic testing the product provides protection in liquids below, above and at the liquid levels. Protection of recessed and hard to reach areas. Complicated valves and the interior surfaces of piping and equipment, which are often difficult or impossible to reach, are protected with true Vapor Corrosion Inhibitor action. Can be applied for hydrotest solution, metalworking fluids, coatings, adhesives and water treatment formulations.

Remarks:

Risk of serious damage to eyes. In case of contact with eyes, rinse immediately with plenty of water & seek medical advice.  Wear suitable gloves and eye / face protection

Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App



Corrosion Inhibitor for Oil and Gas Processing

Size:

Color:

Product Short Description: Corrosion Inhibitor specially used for inhibiting corrosion in Oil and Gas processing and for other oil field application
Product Technical Specification:

Safety and Handling : 

Before handling the chemical products used in this process, the first aid and handling recommendations on the Material Safety Data Sheet for should be read, understood and followed. The industrial cleaning bath is acid and can burn skin and eyes. Refer to the Material Safety Data Sheet for recommendations for protective action.

Remarks:

Corrosion Inhibitor for Oil and Gas Processing are efficient corrosion inhibitors developped to protect oil and gas production installations against internal corrosion. This includes protection of water systems specific to oil fields (produced water disposal systems and production, treatment and injection waters facilities). Corrosion Inhibitor for Oil and Gas Processing offers an optimum corrosion inhibition whatever the fluid characteristics and field conditions: CO2 and/or H2S p

Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App



Premix Glycol Corrosion Inhibited

Size:

Color:

Product Short Description: It is an odorless, colorless, sweet-tasting, viscous liquid.
Product Technical Specification:

Description: Monoethylene Glycol

Test Description

Specification Limits 

Min. Max. 

Unit  of Measure 

Test  Method 

Monoethylene Glycol

50

%(w/w)

Distilled Water

50

%(w/w)                                   ASTM E-203

Acidity (as acetic acid)

0.001

%(w/w)                                 ASTM D-1613

Iron

0.1

ppm                                      ASTM E-202  

DEG

05

%(w/w)                                           SD-498

Aldehyde (as acetaldehyde Chloride)

10

ppm

Ash

0.001

%(w/w)                                          ISI 5295

pH at 20oC

6.5

7.5

Appearance

Clear

Visual

Specific Gravity 20/20oC

1.01

1.01

UV Tansmittance wavelength %

220

70

nm

275

90

nm

350

98

nm

 
Remarks:
Multiple optional colors for leak and fluid identification. All dyes or fluorescences are NSF and food grade. Colors will impede your refractometer results if tested.

 
 
95% Concentrated Inhibited Glycol containers ranging from: 16 oz to 5 gallons and 55 gallons to 275 gallons
West coast stocking location: Salt Lake City, UT.
SE stocking location: Atlanta, GA.
East coast and Mideast stocking location: Taylor, Michigan.
Fast Shipping.
Images: Alt
stock-clearance.png