RXSOL CHEMO PHARMA International Navi Mumbai, India

Products

7,061 products across 71 categories for marine, industrial, water treatment and laboratory use.

Browse all products Product catalogue

Oil Spill Chem & Absorbent

FLOCCULANT 85113

Flocculant is a very effective liquid treatment based on Poly chloride to separate oil residues from bilge water. It is iron-free, and is completely safe to the environment.
Part number
RXSOL-17-3105-210
Brand
RXSOL
FLOCCULANT 85113

Overview

RXSOL Flocculant is a very effective liquid treatment based on  Poly chloride to separate oil residues from bilge water. It is iron-free, and is completely safe to the environment.


Note : The product is to be used as a secondary flocculant along with the cationic primary flocculant for separator effluent oily water unit. the waste water is then treated in an air floatation unit.

Technical specifications

Further Technical Data
Form                            Liquid
Appearance                Clear
Density                        1.3
pH, in conc.                 1.3
Not Compatible Corrosive to cast iron as concentrate. Non-corrosive to all metals at use concentration.

Applications

International environmental regulations set strict rules as to the oil content in effluent water from ships. To meet these regulations, a combination of mechanical and chemical cleaning is necessary. Bilge Water Flocculant is used in combination with multistage bilge water cleaning systems that include mechanical separation of free oil, emulsion breaking, flocculation and filtration. After dosing, Bilge Water Flocculant breaks the oil-in-water emulsion created by contaminants in lubricating and fuel oils, emulsifying cleaning agents etc. It then destabilizes the remaining small oil droplets and agglomerates them into larger particles (flocs) that are easily collected by filtering.

 

Dosage and directions

Typical dose rate: 100 - 500ppm (0.1 - 0.5 litre/m3 of water) In a multistage bilge water cleaning system, Bilge Water Flocculant is fed undiluted through a dosage pump connected to the pressure side of the oil descaler. The floc tank is fed according to the flow of the bilge water pumped into it. The feed is adjusted in connection with the installation and normally needs no alteration. If required, dosing can also be controlled by measuring the level in the container.
 

Characteristics and notes

Features

  • Cost-effective bilge water treatment based on specially selected Poly Aluminium Chloride
  • Iron-free. Completely safe to the environment
  • Acts by both breaking the oil-in-water emulsion and by building flocs
  • Helps to meet environmental regulations on oil content. Discharged water contains normally less than 3 ppm oil
  • Remaining oil sludge can be burned onboard or pumped ashore-contains very little water
  • Low dosage, economical use
  • Effective over an extended pH-range. Eliminates the use of pH-stabilising chemicals
  • Approved by manufacturers of bilge water cleaning systems

Safety and SDS

Read the safety data sheet before handling. Wear suitable gloves and eye protection.

View safety data sheet

Product Name

FLOCCULANT 85113

Product Type

RXSOL-17-3105-210

Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA  

STOCK POINT : Mumbai, Kandla, Chennai, Visakhapatnam, Kolkata, Fujairah

Phone +91 22  27815541 / 42
Fax +91 22 2781 1318 :::AOH :0091 9322594669
Email rxsolchemicals@gmail.com

Hazardous or Regulated Components:
Component Analysis – Inventory

Component CAS CONCENTRATION
ALIPHATIC HYDROCARBON 254504001-5164 20-30
ALCOHOL ALKOXYLATES 254504001-5466 1.5-5
EDTA 6381-92-6 1-5
Properitory Polymer ---------- 30-35
GHS Classification                             Not a hazardous substance or mixture.
Precautionary statements - prevention Wash hands thoroughly after handling.
Precautionary statements - response Get medical advice/ attention if you feel unwell.
Storage:                                                     Store in accordance with local regulations.
Other hazards : Mix thoroughly before use. If swallowed a jelly mass may form which in digestion may cause blockage. Water in contact with the product will cause slippery floor conditions.

 

In case of eye contact : Rinse with plenty of water. Get medical attention if symptoms occur.
In case of skin contact : Wash off with soap and plenty of water. Get medical attention if symptoms occur.
If swallowed:                  Rinse mouth. Get medical attention if symptoms occur.
If inhaled: Get medical attention if symptoms occur.
Protection of first-aiders : In event of emergency assess the danger before taking action. Do not put yourself at risk of injury. If in doubt, contact emergency responders. Use personal protective equipment as required.
Notes to Physician Treat symptomatically. If swallowed a jelly mass may form which in digestion may cause blockage.
Most important symptoms
and effects, both acute and delayed :
See Section 11 for more detailed information on health effects and symptoms.
Suitable extinguishing media :    Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
Unsuitable extinguishing  media:    Do not use water unless flooding amounts are available.
Specific hazards during firefighting :  Not flammable or combustible.
Hazardous combustion products : Decomposition products may include the following materials: Carbon oxides nitrogen oxides (NOx)
Special protective equipment for firefighters : Use personal protective equipment.
Specific extinguishing methods : Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations.

 

Personal precautions, protective equipment and emergency procedures: Spills of this product are very slippery. Refer to protective measures listed in sections 7 and 8.
Environmental precautions : No special environmental precautions required.
Methods and materials for containment and cleaning up : Stop leak if safe to do so. Contain spillage, and then collect with noncombustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite) and place in container for disposal according to local / national regulations (see section 13). Flush away traces with water. For large spills, dike spilled material or otherwise contain material to ensure runoff does not reach a waterway.

 

Advice on safe handling: Stir well prior to use.
Conditions for safe storage: Keep out of reach of children. Keep container tightly closed. Store in suitable
labelled containers. Store separately from oxidizers.
Suitable material:           The following compatibility data is suggested based on similar product data and/or industry experience: Compatibility with Plastic Materials can vary; we therefore recommend that compatibility is tested prior to use., Stainless steel, Polyethylene.
Unsuitable material:

Not determined

Components with workplace control parameters :

Exposure guidelines have not been established for this product. Available exposure limits for the substance(s) are shown below.

Components CAS No.       Form of exposure Permissible Concentration Basis
Hydrotreated Light Distillate 64742-47-8 TWA (Mist) 5 mg/m3 AU OEL          
Hydrotreated Light Distillate 64742-47-8 TWA (Mist) 5 mg/m3 NZ OEL          
    WES-STEL (Mist) 10 mg/m3 NZ OEL 
Hydrotreated Light Distillate 64742-47-8 TWA  500 ppm
2,000 mg/m3
OSHA Z1
    TWA 200 mg/m3
(as total hydrocarbon vapor)
ACGIH
    TWA (Mist)  5 mg/m3 OSHA Z1
    TWA (Mist) 5 mg/m3 NIOSH REL
    STEL (Mist) 10 mg/m3 NIOSH REL
Engineering   
Measure         
Good general ventilation should be sufficient to control worker exposure to airborne contaminants.
Personal Protection

Eye protection : Safety glasses
Hand protection : Wear protective gloves. Gloves should be discarded and replaced if there is any indication of degradation or chemical breakthrough.
Skin protection : Wear suitable protective clothing.

Respiratory protection: No personal respiratory protective equipment normally required.
Hygiene measures: Wash hands before breaks and immediately after handling the product.

                                       

        Gloves                       Suit                          

 

Appearance :        Emulsion
Colour: White
Odour: Hydrocarbon-like
Flash Point Does not flash
pH: 9, 1 %
Odour Threshold : No data available
Melting Point: No data available
Boiling Point: No data available
Evaporation Rate: No data available
Flammability (solid, gas): No data available
Explosive limits upper: No data available
Explosive limits Lower: No data available
Vapour pressure: No data available
Relative Vapour Density: No data available
Relative density : 1.110 - 1.150, (22 °C)
Water solubility : Dispersible
Solubility in other solvents : No data available
Partition coefficient noctanol: No data available
Autoignition Temperature: No data available
Thermal decomposition
temperature:
No data available
Viscosity dynamic : 400 - 1,500 mPa.s (25 °C)
Viscosity, kinematic: No data available
Molecular Weight: No data available
VOC : 23.0 %
Chemical stability:                      Stable under normal conditions.
  Product is stable.
Possibility of hazardous reactions: No dangerous reaction known under conditions of normal use.
Conditions to avoid None known.
Incompatible materials Addition of water results in gelling.Contact with strong oxidizers (e.g. chlorine, peroxides, chromates, nitric acid, perchlorate, concentrated oxygen, permanganate) may generate heat, fires, explosions and/or toxic vapors.
Hazardous Decomposition Products Decomposition products may include the following materials:
Carbon oxides
Nitrogen oxides (NOx)
Hazardous Polymerization Hazardous polymerization does not occur.
                          Inhalation, Eye contact, Skin contact
Potential Health Effects  
Eyes :                                                      Health injuries are not known or expected under normal use.
Skin : Health injuries are not known or expected under normal use.
Ingestion : If swallowed a jelly mass may form which in digestion may cause blockage.
Inhalation : Health injuries are not known or expected under normal use.
Chronic Exposure : Health injuries are not known or expected under normal use.
Experience with human exposure  
Eye contact : No symptoms known or expected.
Skin contact : No symptoms known or expected.
Ingestion :                                     No symptoms known or expected.
Inhalation : No symptoms known or expected.
Toxicity   Product  
Acute oral toxicity :  Acute toxicity estimate: > 2,000 mg/kg
Acute inhalation toxicity : No data available
Acute dermal toxicity :               No data available
Skin corrosion/irritation : No data available
Serious eye damage/eye irritation : Result: Mild eye irritation
Respiratory or skin sensitization : No data available
Carcinogenicity : No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC.
Reproductive effects : No toxicity to reproduction
Germ cell mutagenicity : Contains no ingredient listed as a mutagen
Teratogenicity : No data available
STOT - single exposure : No data available
STOT - repeated exposure : No data available
Human Hazard Characterization Based on our hazard characterization, the potential human hazard is: Low
Ecotoxicity Environmental Effects : This product has no known ecotoxicological effects.
Toxicity to Fish                                Not Available
Toxicity to daphnia and other
aquatic invertebrates
No Data available.
Toxicity to algae : No Data available.
Components  
Toxicity to fish : Hydrotreated Light Distillate
LC50 : > 1,000 mg/l
Exposure time: 96 h
Toxicity to daphnia and other
aquatic invertebrates:
Hydrotreated Light Distillate
EC50 : > 1,000 mg/l
Exposure time: 48 h
Toxicity to algae : Hydrotreated Light Distillate
EC50 : > 1,000 mg/l
Exposure time: 72 h
Toxicity to bacteria : Hydrotreated Light Distillate
> 1,000 mg/l
Exposure time: 48 h
Persistence and degradability: The organic portion of this preparation is expected to be poorly biodegradable.
Mobility

The environmental fate was estimated using a level III fugacity model embedded in the EPI (estimation program interface) Suite TM, provided by the US EPA. The model assumes a steady state condition between the total input and output. The level III model does not require equilibrium between the defined media. The information provided is intended to give the user a general estimate of the environmental fate of this product under the defined conditions of the models. If released into the environment this material is expected to distribute to the air, water and soil/sediment in the approximate respective percentages;
Air : <5%
Water : 10 - 30%
Soil : 50 - 70%
The portion in water is expected to be soluble or dispersible.

Bioaccumulative potential This preparation or material is not expected to bioaccumulate.
Other Information no data available
ENVIRONMENTAL HAZARD AND EXPOSURE CHARACTERIZATION
Based on our hazard characterization, the potential environmental hazard is: Low

Disposal methods :

Where possible recycling is preferred to disposal or incineration. If recycling is not practicable, dispose of in compliance with local regulations. Dispose of wastes in an approved waste disposal facility.

Disposal considerations :

Dispose of as unused product. Empty containers should be taken to an approved waste handling site for recycling or disposal. Do not re-use empty containers.

Trasport Informatioon The shipper/consignor/sender is responsible to ensure that the packaging, labeling, and markings are in compliance with the selected mode of transport.
Land Transport  
Proper shipping name PRODUCT IS NOT REGULATED DURING TRANSPORTATION
Air transport (IATA)  
Proper shipping name PRODUCT IS NOT REGULATED DURING TRANSPORTATION
Sea transport (IMDG/IMO)  
Proper shipping name PRODUCT IS NOT REGULATED DURING TRANSPORTATION
Standard for the Uniform Scheduling of Medicines and Poisons :   No poison schedule numb
INTERNATIONAL CHEMICAL CONTROL LAWS :  
TOXIC SUBSTANCES CONTROL ACT (TSCA) This product has not been evaluated for TSCA and may contain substances not found on the TSCA 8(b) Inventory List. This product may be used under the TSCA 5(h)(3) Research Exemption if all requirements are met.
CANADIAN ENVIRONMENTAL PROTECTION ACT (CEPA) This product contains substance(s) which are not listed on the Domestic Substances List (DSL) or the NonDomestic Substances List (NDSL).
AUSTRALIA All substances in this product comply with the National Industrial Chemicals Notification & Assessment Scheme (NICNAS).
CHINA All substances in this product comply with the Provisions on the Environmental Administration of New Chemical Substances and are listed on or exempt from the Inventory of Existing Chemical Substances China (IECSC).
JAPAN All substances in this product comply with the Law Regulating the Manufacture and Importation Of Chemical Substances and are listed on the Existing and New Chemical Substances list (ENCS).
KOREA All substances in this product comply with the Chemical Control Act (CCA) and are listed on the Existing Chemicals List (ECL)
PHILIPPINES

All substances in this product comply with the Republic Act 6969 (RA 6969) and are listed on the Philippines Inventory of Chemicals & Chemical Substances (PICCS).

Other Information  

The information above is believed to be accurate and represents the  best information   currently    available  to us.  However,   we   make no warranty of merchantability or any other warranty, express or implied, with respect to such information, and  we assume  no liability resulting from its use. Users should make  their  own  investigations  to determine the suitability of the information for their particular purposes. In no event shall be liable for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental, consequential or exemplary damages, howsoever arising, even if RX Marine International  has been advised of the possibility of such damages.

DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.

Request the signed SDS as PDF

Availability

FLOCCULANT 85113 manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai, Sharjah, UAE, Gulf, Middle East, Muscat Oman, Kenya Africa. Get the best quality of FLOCCULANT 85113 at a competitive price from us. We have ready stock of FLOCCULANT 85113 in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.

Our stock points and branches