Power Plant / Heavy Industries
Carbon Cleaner LT
- Part number
- RXSOL-16-1075-025
- Category
- Power Plant / Heavy Industries
- Brand
- RXSOL
Overview
Carbon Remover LT is a non-corrosive, powerful solvent for removal of carbonaceous deposits. Carbon Remover LT contains no chlorinated solvents or phenolic compounds and has low toxicity to the environment and to persons handling it. ::: ( This product is WATER INSOLUBLE )
Our Other Valuable grade of CARBON REMOVER :::
A) Carbon Remover Part No. - RXSOL-16-1003-025 ::: Specifically formulated for removal of completely carbon, grease, oil, varnishes and other heavy deposits from diesel engine. RXSOL-16-1003-025 is a highly concentrated Wetting Emulsifying Agent which makes this product water soluble. ( This product is WATER SOLUBLE )
This powerful action is based on a two –Layer mechanism. The top-layer prevents the evaporation of the volatile components in the button-layer. The button –layer removes the deposited substances. This way, the deposits are bind and trapped resulting to complete and safe removal.
CARBON cleaner is very active which eliminates the need for Scrubbing or Brushing which can cause mechanical damages to discs and result in poor performance.
A)Decarbonizer Predator Carbon Cleaner Part No. - RXSOL-16-1699-025 ::: Fast Effective Liquid degreaser and decarbonizer, Its immediate action of solvent makes it very popular and easy to use. Plesant Smell based and its specialization is water-rinseable gives complete cleaning effect. ( This product is WATER INSOLUBLE )
Technical specifications
|
APPEARANCE |
Pale yellow liquid |
|
DENSITY, in g/cm3 at 15°C |
1.0 |
|
FLASH POINT, (PMCC) in °C |
Above 61 |
|
pH, in conc. |
N/A |
|
COMPATIBILITY |
|
|
Metal |
No known effect |
|
Rubber |
May swell |
|
Synthetic rubber |
May swell |
Dosage and directions
This is an effective way of cleaning deposits from machine parts. The items to be cleaned are dipped into the solvent. A wire basket can be used for small components. For removal of light deposits or oil, a dilution of up to 1:2 in fresh water can be used. Light deposits will be removed in 1 hour, whereas heavily oxidized deposits may need overnight soaking. After the components have been removed from the soaking bath, remaining solvent is easily flushed off with water. Due to a very low evaporation rate, no precautions are necessary to prevent loss of liquid, but adequate ventilation is recommended. Cleaning the Oil Side of Heat Exchangers Where in-situ cleaning is required, Carbon Remover LT can be used neat and circulated through the unit in question. Time required for this process will again depend on extent of fouling and may take up to 24 hours. recommended to be used.
- Disconnect the heat exchanger's oil inlet and outlet, drain off any remaining oil.
- Connect the discharge side of the Chemical Cleaning Unit (CCU) to the lower heat exchanger connection and fit the return to the CCU.
- Add Carbon Remover LT to the drum and heat, maintaining the temperature (max 60°C), throughout the cleaning operation. If heat is not available the cleaning time will need to be extended.
Circulate for 12 hours. When the cleaning is complete, disconnect the lower heat exchange connection and
Characteristics and notes
Features, Benefits and Applications
- Reformulated with improved cleaning properties
- Can be used for cleaning engine parts like:
- Pistons
- Piston rings
- Valves
- Valve cages
- Does not contain nonyl phenol ethoxylates or other
- estrogenic compounds Non-corrosive, safe on all light metals, including aluminum
- Quickly dissolves deposits containing carbon, resins or varnishes
- Simple and economical to use by soaking or circulation method
- Low toxicity
- Low evaporation rate
- No phenolic or chlorinated compounds
- Can be used for removal of carbon type deposits from
- burner tips, fuel injectors and all components fouled by
Safety and SDS
Read the safety data sheet before handling. Wear suitable gloves and eye protection.
View safety data sheet
| Product Name | RXSOL-16-1075-025 |
| Product Type | Carbon Cleaner LT |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Kandla, Chennai, Visakhapatnam, Kolkata, Fujairah, Muscat
| Phone | +91 22 27815541 / 42 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| rxsolchemicals@gmail.com |
|
Chemical Name |
Concentration |
CASNumber |
ECNumber |
RPhrases* |
Symbols |
|
1,2-Dichlorobenzene |
30-60 |
95-50-1 |
202-425-9 |
22, 36/37/38, 50/53 |
Xn, N |
|
Xylenol |
10-30 |
1300-71-6 |
215-089-3 |
24/25, 34, 51/53 |
T, N |
|
Kerosine, unspecified |
10-30 |
64742-94-5 |
265-198-5 |
65, 66, 51, 53 |
Xn, N |
|
Naphtha(petroleum), |
10-30 |
64742-82-1 |
265-185-4 |
65, 66 |
Xn |
|
2-BUTOXY ETHANOL |
ppm 20 ppm |
111-76-2 50 |
|||
|
Ammonium Hydroxide |
50 ppm - 20 ppm |
1336-21-6 |
|||
|
Ethyl Alcohol |
1000 ppm |
64-17-5 |
*SeeSection16
|
Odour |
Unpleasant odour, Strong smell of phenol |
|
Appearance |
Liquid, brown, dispersible in water |
|
Contact with eyes |
Can cause damage to the eyes |
|
Contact with skin |
Causes burns (R34), Toxic in contact with skin and if swallowed (R24/25) |
|
Inhalation |
May cause sever eirritation, May cause dizziness, confusion, headache or stupor, In cases of severe exposure, anaesthesia may develop |
|
Ingestion |
Toxic if swallowed (R25) Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment (R50/53) |
|
Contact with skin |
Remove contaminated clothing immediately and drench affected skin with plenty of water.Then wash with soap and water. Whenin doubt or symptoms persist, seek medical attention.Contamin ated clothing should be laundered befor ereuse |
|
Contact with Eyes |
If substance has got into eyes, immediately wash out with plenty of water forat least 15 minute.Irrigate eyes thoroughly whilst lifting eyelids.Seek immediate medical attention.Continue flushing with water until medical help arrives |
|
Ingestion |
Never make an unconscious person vomit or drink fluids.Give plenty of water to drink.Do not induce vomiting.Seek immediate medical attention. |
|
Inhalation |
Remove patient to fresh air.Keep warm and at rest, in a half upright position. Loosen clothing.When in doubt or symptoms persist, seek medical attention |
|
General |
In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) (S45) |
- Flash point & gt;70 deg C (CC)
- Decomposition products may include phosgene, Decomposition products may include carbon oxides
- In case of fire use water spray or fog, alcohol resistant foam, dry chemical or carbon dioxide (S43)
- Substance evolves toxic fumes, wear self-contained breathing apparatus
- Prevent run off water from entering drains if possible
- Use water spray or fog to knock down and absorb corrosive fumes
- Vapours are heavier than air and may travel considerable distances to a source of ignition and flash back
|
Personal Precautions |
Wear protective clothing as per section 8.Vapours are heavier than air and may travel considerable distances to a source of ignition and flash back. |
|
Environmental Precautions |
Do not allow to enter public sewers and water courses |
|
Immediate Actions |
Use appropriate containment to avoid environmental contamination (S57) |
|
Clean Up Actions |
Absorb spillage in inert material and shovel up.Ventilate the area and wash spill site after material pick-up is complete |
|
Special Precautions |
Wear protective clothing as per section 8.Avoid release to the environment. Refer to special in structions/Safety data sheets (S61).Vapours are heavier than air and may travel considerable distances to a source of ignition and flash back |
|
Handling |
See Section 8.Eye wash bottles should be available. Avoid contact with skin and eyes(S24/25). |
|
Storage |
Keep only in the original container in a cool, well ventilated place (S3/9/49). |
|
ExposureLimits |
TLV (TWA) 20ppm, 122mg/m3 (1,2-Dichlorobenzene) |
|
Exposurecontrols |
The undiluted product must not be used in a confined space without good ventilation |
|
Occupational exposure controls |
Wear approved respirator if exposure likely to exceed MEL / OES . Wear goggles giving complete eye protection. Wear suitable protective clothing, in cluding eye/ face protection and gloves (neoprene or nitrileare recommended) |
Gloves Goggles Suit Respirator
| Odour | Unpleasant odour, Strong smell of phenol |
| Appearance | Liquid, brown, dispersible in water |
| pH | 10-11 (5%in50/50 H2O-IPA mix) |
| Boiling point & gt | 100° Cat 760 mm / Hg |
| Vapour pressure | not known |
| Vapour density | (air =1) & gt;01 |
| Freezing point | <0°Cat 760mm / Hg |
| Insoluble in water | |
| Specific gravity | (water=1) 1.02 |
| Flash point & gt | 70 deg C (CC) |
- This article is considered stabl eunder normal conditions, May cause rubber to swell
- Avoid overheating
- In compatible with strongo xidizing substances, Contact with alkaline earth gases, Contact with alkali metals may
forme xplosive gases
- See Section 5
|
Toxicological information |
In cases of severe exposure, nausea/vomiting may develop |
|
Inhalation |
Causes seve re irritation |
|
Has central nervous systeme ffects |
|
|
May cause nausea/ vomiting |
|
|
Contact with skin |
Canbe absorbed through skin |
|
Toxic by inhalation and in contact with skin (R23/24) |
|
|
Causes burns ( R34 ) |
|
|
Contact with eyes |
Causes severe irritation |
|
Can cause damage to the eyes |
|
|
Ingestion |
Can cause damage to the digestive system |
|
Toxic if swallowed (R25) |
|
|
Carcinoge ni city |
No evidence of carcino genic effects |
| Ecotoxicity | This product contains components which are classified in the EU as dangerous for the environment. |
| Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment (R50/53) | |
| Mobility | Emulsifies in water |
| Persistence and Biodegradability | Most components in this product are not readily biodegradable |
| Bioaccumulation Potential | Hydrocarbon solvents have the potential to bioaccumilate. |
| Other Adverse Effects | No environmental problems are expected when the product is used / handled correctly. In its intended use, the product will not be released into the environment. |
Classification:
- This material and/or its container must be disposed of as hazardous waste
- EU Waste class: 07.01
Disposal considerations:
- Do not discharge into drains or the environment, dispose to an authorised waste collection point
- Disposal should be in accordance with local, state or national legislation
| Proper Shipping Name: | ||||
| UN | ||||
| Proper Shipping Name | Toxicliquid organic, n.o.s | (Xylenol, 1,2-dichlorobenzene) | ||
| UN NO. | 2810 | |||
| Hazard Class | 6.1 | PackingGroup | III | |
| Road/Rail(ADR/RID) | ||||
| Proper Shipping Name | Toxicliquid, organic, n.o.s. | (Xylenol, 1,2-dichlorobenzene) | ||
| ADR UN No. | 2810 | |||
| ADRHazardClass | 6.1 | Tremcard | 61GT1-III | |
| Sear (IMDG) | ||||
| Proper Shipping Name | Toxicliquid, organic, n.o.s. | (Xylenol,1,2-dichlorobenzene) | ||
| IMDG UN No. | 2810 | |||
| IMDG Hazard Class | 6.1 | ICAO PackingGroup | III | |
| IMDG EmS | F-A, S-A | IMDG subrisk: | N/A | |
| IMDG Labels | 6.1+Mar | Pollutant | ||
| IMDG Flashpoint | >70°C | |||
| Air(ICAO/IATA) | ||||
| Proper Shipping Name | Toxicliquid, organic, n.o.s. | (Xylenol, 1,2-dichlorobenzene) | ||
| ICAO UnNo | 2810 | |||
| ICAO HazardClass | 6.1 | ICAO PackingGroup | III | |
| ICAO subrisk | N/A | ICAO Labels | 6.1 | |
| ICAO Flashpoint | >70°C | |||
| DOT/ CFR(USDepartment ofTransportation | ||||
| DOT Proper Shipping Name | Toxicliquid, organic, n.o.s. | (Xylenol, 1,2-dichloro benzene) | ||
| Hazardous Material | Xylenol | 1,2-dichloro benzene | ||
| Hazard Class | 6.1 | Identification Number | UN2810 | |
| Product RQ (lbs) | 100 | DOT subrisk: | Marine Pollutant | |
| DOT Labels | 6.1+Mar | Pollutant | ||
| DOT Flash point | >70°C | |||
Risk Phrases :
Harmfulby inhalation(R20).Toxic in contact with skin and ifswallowed(R24/25).Causes burns(R34). Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatice nvironment (R50/53)
Safety Phrases:
Do not breathe vapour/ fumes (S23) In case of contact with eyes, rins eimmediately with plenty of water and seek medical advice (S26) After contact with skin, wash immediately with plenty of soap and water (S 28 )If swallowed, do not induce vomiting: seek medica ladvice immediately and show this container or label ( S62 ). Wear suitable protective clothing, eye/face protection and gloves (S36/37/39).This material and its container must be disposed of as hazardous waste (S60).Avoid release to the environment. Refer to specia linstructions /Safety data sheets ( S61)
Text of R and S phrase codes used in this safety data sheet:-
|
R 22: |
Harmful if swallowed; |
|
R24/25 |
Toxic in contact with skin and if swallowed; |
|
R34 |
Causes burns |
|
R 36/37/38 |
Irritating to eyes, respiratory system and skin; |
|
R 50/53 |
May cause long term adverse effect in the aquatic environment; |
|
R65 |
Harmful: may cause lung damage if swallowed; |
|
R66 |
Repeated exposure may cause skin dryness or cracking.The information |
provided about the product on this Safety Data Sheet hasbeen compiled from knowledge of the individual constituents.The data given here is base don current knowledge and experience.This Safety Data Sheet describes the product In terms of safety requirements and does not signify any warranty with regard to the product's properties.The data given here only applies when product used for proper application (s). The product is not sold as suitable for other applications- usage in such may cause risks not mentioned in this sheet. Do not use for other application (s) with out seeking advice from manufacturer Composition information in accordance with Regulation (EC) No 648/2004 of the European Parliament and of the Council of 31 March 2004 on detergents:
|
Halogenated hydrocarbons |
30 % |
|
Aromatic hydrocarbons |
30 % |
|
Aliphatic hydrocarbons |
5-15 % |
|
Anionic surfactants |
5-15 % |
AMMONIUM HYDROXID 26BE 1336-21-6 50 ppm 20 ppm Yes
ETHYL ALCOHOL 64-17-5 1000 ppm 1000 ppm No
Availability
Carbon Cleaner LT manufacturer, supplier and exporter in Mumbai, Navi Mumbai MIDC, Gandhidham, Kolkata, Chennai, Visakhapatnam, Fujairah, Sharjah, Abudhabi, Dubai, Ajman, Sohar, Muscat, Barka Oman
