|
Product Name |
Para Nitrophenol |
|
Part Number |
RXSOL-60-6605-993 |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Branch : Kandla, Mumbai , Chennai, Vizag, Kolkata, UAE , OMAN , CANADA and KENYA
|
Phone |
+91 22 20871200 - 1400 |
|
Fax |
+91 22 27612100 :::AOH :0091 9821214367 |
|
Email |
rxsolchemicals@gmail.com |
|
Website |
www.rxmraine.comA |
|
Chemical Name |
CAS |
EC number |
Weight |
Formula |
|
Para Nitrophenol |
100-02-7 |
202-811-7 |
<= 100 % |
C6H5NO3 |
|
Signal Word |
Warning |
|
Hazard Statements |
H302 + H312 + H332 Harmful if swallowed, in contact with skin or if inhaled. H373 May cause damage to organs through prolonged or repeated exposure. H373 May cause damage to organs (Kidney, Liver) through prolonged or repeated exposure if swallowed. |
|
Precautionary statements |
P260 Do not breathe dust. P280 Wear protective gloves/ protective clothing. P301 + P312 IF SWALLOWED: Call a POISON CENTER/ doctor if you feel unwell. P302 + P352 + P312 IF ON SKIN: Wash with plenty of water.Call a POISON CENTER/ doctor if you feel unwell. P304 + P340 + P312 IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER/ doctor if you feel unwell. P314 Get medical advice/ attention if you feel unwell. |
|
Classification of the substance or mixture |
Not a hazardous substance or mixture according to Regulation (EC) No 1272/2008. |
|
Supplemental Hazard Statements |
None. |
|
Other hazards |
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher. |
|
General advice |
Show this material safety data sheet to the doctor in attendance. |
|
If inhaled |
After inhalation: fresh air. Immediately call in physician. If breathing stops: immediately apply artificial respiration, if necessary also oxygen. |
|
Eye Contact |
After eye contact: rinse out with plenty of water. Call in ophthalmologist. Remove contact lenses. |
|
Swallowed |
After swallowing: immediately make victim drink water (two glasses at most). Consult a physician. |
|
Skin Contact |
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Consult a physician. |
|
Inhalation |
Remove patient to fresh air, keep warm and at rest and get medical assistance in necessary. |
|
Ingestion |
Rinse mouth with water. Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a doctor or Poison Control Center immediately. |
|
Most important symptoms and effects, both acute and delaye |
The most important known symptoms and effects are described in the labelling (see section 2.2) and/or in section 11 |
|
Indication of any immediate medical attention and special treatment needed |
No data available |
|
Flammability |
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide. |
|
Flash Point |
Dry powder Dry sand |
|
Suitable extinguishing media |
Water Foam Carbon dioxide (CO2) Dry powder |
|
Unsuitable extinguishing media |
For this substance/mixture no limitations of extinguishing agents are given. |
|
Special hazards arising from the substance or mixture |
Carbon oxides Nitrogen oxides (NOx) Combustible. Vapors are heavier than air and may spread along floors. Forms explosive mixtures with air on intense heating. Development of hazardous combustion gases or vapours possible in the event of fire. |
|
Further information |
Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system. |
Hazardous combustion
products |
Fire may cause the evolution of Sulphur oxides, nitrogen oxides. |
|
Advice for firefighters |
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing. |
|
Protective Equipment |
Use personal protective equipment. |
|
Specific Hazards Arising from the Chemical |
Oxides of phosphorus Sodium oxides Not combustible. Fire may cause evolution of: Oxides of phosphorus Ambient fire may liberate hazardous vapours. |
|
Personal precautions, protective equipment and emergency procedures |
Advice for non-emergency personnel: Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert. For personal protection see section 8. |
|
Spillage |
Oxidizing material. Stop leak if without risk. Avoid contact with a combustible material (wood, paper, oil, clothing...). Keep substance damp using water spray. Do not touch spilled material. Prevent entry into sewers, basements or confined areas dike if needed. Eliminate all ignition sources. Call for assistance on disposal. |
|
Enviromental Precaution |
Do not let product enter drains. |
Methods and materials for
containment and cleaning |
Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up dry. Dispose of properly. Clean up affected area. Avoid generation of dusts. |
|
Advice on protection against fire and explosion |
Keep away from open flames, hot surfaces and sources of ignition. |
|
Incompatible materials |
Keep away from alkalis, strong oxidizing agents and metals. Provide containment walls of adequate capacity to hold any accidental spills. |
|
Hygiene measures |
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance. For precautions see section 2.2. |
|
Precautions for safe handling |
Work under hood. Do not inhale substance/mixture. |
|
Storage conditions |
Tightly closed. Dry. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorized persons. |
|
Storage class |
Storage class (TRGS 510): 6.1C: Combustible, acute toxic Cat.3 / toxic compounds or compounds which causing chronic effects |
|
Specific end use(s) |
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated |
|
Advice on general occupational hygiene |
Advice on safe handling Observe label precautions. Change contaminated clothing. Wash hands after working with substance. |
|
Requirements for storage |
Keep in cool and store under shade. |
|
Exposure controls |
Appropriate engineering controls Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday. |
|
Control parameters |
Ingredients with workplace control parameters Contains no substances with occupational exposure limit values. |
|
Engineering Control |
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday. |
|
Eye/face protection |
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses |
|
Body Protection |
Protective clothing |
|
Skin protection |
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de). Full contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:KCL 741 Dermatril® L This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de). Splash contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:KCL 741 Dermatril® L |
|
Respiratory protection |
Required when dusts are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type P2 The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented. |
|
Other Protection Measure |
Handle in accordance with good industrial hygiene and safety practice. |
|
Control of environmental exposure |
Do not let product enter drains. |
|
Physical state |
Solid |
|
Colour |
Yellow |
|
Odour |
Characteristic |
|
Odor Threshold |
No data available |
|
pH |
4,4 at 5 g/l at 24 °C |
|
Melting Point |
110 - 115 °C - lit. |
|
Boiling Point |
279 °C |
|
Flash Point |
169 °C |
|
Evaporation Rate |
Not Applicable |
|
Flammability (solid, gas) |
No data available |
|
Explosive limits |
No Data Available |
|
Upper/lower flammability or explosive limits |
No data available |
|
Autoignition temperature |
No data available |
|
Decomposition temperature |
> 280 °C |
|
Vapour pressure |
No data available |
|
Density |
1,48 g/cm3 at 20 °C |
|
Relative Density |
No data available |
|
Relative vapor density |
No data available |
|
Freezing point |
No data available |
|
Viscosity |
No data available |
|
Partition coefficient |
log Pow: 1,95 |
|
Explosive properties |
No data available |
|
Solubility |
14,8 g/l at 25 °C |
|
Ignition temperature |
No information available. |
|
Particle characteristics |
No data available |
|
Reactivity |
Forms explosive mixtures with air on intense heating. A range from approx. 15 Kelvin below the flash point is to be rated as critical. The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed. |
|
Stability |
The product is chemically stable under standard ambient conditions (room temperature) . |
|
Possibility of hazardous reactions |
Risk of explosion with: Reducing agents conc. sulfuric acid Risk of ignition or formation of inflammable gases or vapours with: alkalines alkali hydroxides |
|
Conditions to avoid |
Strong heating. |
|
Incompatible materials |
No data available |
|
Hazardous decomposition products |
In the event of fire: see section 5 |
|
Acute toxicity |
LD50 Oral - Rat - 667 mg/kg Remarks: (ECHA) LC50 Inhalation - Rat - 4 h - 4,7 mg/l - dust/mist Remarks: (External MSDS) Acute toxicity estimate Inhalation - 4,7 mg/l - dust/mist (Calculation method) LD50 Dermal - Rat - 1.024 mg/kg Remarks: (RTECS) Acute toxicity estimate Dermal - 1.024 mg/kg (Calculation method) |
|
Skin corrosion/irritation |
Remarks: No data available |
|
Serious eye damage/eye irritation |
Remarks: No data available |
|
Respiratory or skin sensitization |
No data available |
|
Toxic Effects on Human |
May cause damage to the following organs: upper respiratory tract. Other Toxic Effects on Humans: Hazardous in case of skin contact (irritant, sensitizer), of ingestion, of inhalation (lung irritant, lung sensitizer). |
|
Carcinogenicity |
No data available |
|
Germ cell mutagenicity |
Test Type: Ames test Test system: Escherichia coli/Salmonella typhimurium Metabolic activation: with and without metabolic activation Result: negative |
|
Reproductive toxicity |
No data available |
|
Specific target organ toxicity - single exposure |
No data available |
|
Special Remarks on other Toxi Effects on Humans |
Acute Potential Health Effects: Skin: Causes skin irritation. May cause skin sensitization, an allergic reation, which becomes evident upon re-exposure to this material. Eyes: Causes eye irritation. Ingestion: Causes gastrointestinal (digestive) tract irritation with nausea, vomiting, and diarrhea. May be harmful if swallowed. Inhalation: Causes respiratory tract irritation. May cause chemical pneumonitis and pulmonary edema, inflammation, edema of bronchi and larynx. Chronic Potential Health Effects: Repeated or prolonged skin exposure may cause allergic reactions in sensitive individuals. Repeated or prolonged exposure by inhalation may affect respiration and metabolism. |
|
Endocrine disrupting properties |
The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher. RTECS: SM2275000 Absorption into the body leads to the formation of methemoglobin which in sufficient concentration causes cyanosis. Onset may be delayed 2 to 4 hours or longer., Depending on the intensity and duration of exposure, effects may vary from mild irritation to severe destruction of tissue., Damage to the eyes. To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated. |
|
Bioaccumulative potential |
Bioaccumulation Pimephales promelas (fathead minnow) - 28 d - 0,0441 mg/l(4-Nitrophenol) Bioconcentration factor (BCF): 280 |
|
Persistence and degradability |
Biodegradability Result: 97 % - Readily biodegradable. (OECD Test Guideline 301A) |
|
Toxicity to fish |
LC50 - Lepomis macrochirus (Bluegill) - 0,24 mg/l - 96 h |
|
Toxicity to daphnia and other aquatic invertebrates |
Flow-through test EC50 - Ceriodaphnia dubia (water flea) - 0,035 mg/l - 48 h (OECD Test Guideline 202) |
|
Toxicity to algae |
EC50 - Desmodesmus subspicatus (green algae) - 23,7 mg/l - 96 h |
|
Toxicity to bacteria |
EC5 - Pseudomonas putida - 0,9 mg/l - 16 h Remarks: (IUCLID) |
|
Mobility in soil |
No Information available |
|
Results of PBT and vPvB assessment |
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher. |
|
Endocrine disrupting properties |
The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher. |
|
Other adverse effects |
No data available |
|
Disposal methods |
The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems. |
|
Contaminated packaging |
Dispose of as unused product. |
|
Waste treatment Method |
No data available |
|
UN number |
ADR/RID: 1663 IMDG: 1663 IATA: 1663 |
|
UN proper shipping name |
ADR/RID: Nitrophenols IMDG: Nitrophenols IATA: Nitrophenols |
|
Transport hazard class(es) |
ADR/RID: 6.1 IMDG: 6.1 IATA: 6.1 |
|
Packaging group |
ADR/RID: III IMDG: III IATA: III |
|
Environmental hazards |
ADR/RID: NO IMDG: NO IATA: NO |
|
Further information |
No data available |
|
Inventory status |
Components are on the following inventories: Polymaleic acid: - US TSCA, Canadian DSL, EU EINECS, Australian AICS, Korean, Philippine PICCS and Chinese Xi irritant R 36/38 Irritant to eyes & skin R 41 Risk of serious damage to eyes S24/25 Avoid contact with skin and eyes S26/28 In case of contact eyes & skin, rinse with plenty water and seek medical advice Section 312/313: Not listed. Not listed under California proposition 65. |
|
Safety, health and environmental regulations/legislation specific for the substance or mixture |
This material safety data sheet complies with the requirements of Regulation (EC) No. 1907/2006. |
|
National legislation |
Seveso III: Directive 2012/18/EU of the European Parliament and of the Council on the control of major-accident hazards involving dangerous substances. : ACUTE TOXIC : ENVIRONMENTAL HAZARDS |
|
Other regulations |
Observe work restrictions regarding maternity protection in accordance to Dir 92/85/EEC or stricter national regulations where applicable. Take note of Dir 94/33/EC on the protection of young people at work. |
|
Chemical Safety Assessment |
For this product a chemical safety assessment was not carried out |
|
Other Information |
The information above is believed to be accurate and represents the best information currently available to us. However, we make no warranty of merchantability or any other warranty, express or implied, with respect to such information, and weassume no liability resulting from its use. Users should make their own investigations to determine the suitability of the information for their particular purposes. In no event shall be liable for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental, consequential or exemplary damages, howsoever arising, even if Rx Marine International has been advised of the possibility of such damages.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
|
