RXSOL 202
- Part number
- RXSOL-20-2073-210
- Category
- Tank Cleaner
- Brand
- RXSOL
Overview
RXSOL 202 is a very powerful heavy duty alkaline cleaning and degreasing agent. RXSOL 202 is based on strong anionic surfactants and alkaline salts.
Technical specifications
|||
| 1.15 | 1 |
|---|---|
| 1.15 | 1 |
Applications
RXSOL 202 is used for general cleaning, tank cleaning and boiler cleaning. RXSOL 202 is especially good for cleaning soot and inert gas(IG) stains, as well as vegetable oils, and some mineral oils. RXSOL 202 works well on many ANNEX II cargoes and ANNEX I cargoes as well.
Dosage and directions
Tank Cleaning:
Before cleaning with RXSOL 202 it is recommended to pre-wash with hot water. For drying or semi-drying oils a prewash with cold water should be carried out immediately after discharge of cargo to retard oxidation and hardening of oil residues. After 1 cycle slowly start to in-crease the water temperature to increase effectiveness of the prewash.
Reciculation Method:
Recirculation is highly effective. In this method a chemical solution is pumped via a closed loop through a mechanical tank washing machine. The chemical solution is normally prepared in the tank to be cleaned or in the slop tank. Heat is achieved by the use of a heat exchanger, steam coils or live steam injection. The advantages of this method are the recovery of the heat and chemicals to clean additional tanks. RXSOL 202 is circulated as a 1 - 3 % solution > 70 °C for a period of 2 - 6 hours. After circulation rinse thoroughly with water.
Depending on the degree of contamination one solution can be used to wash 1 - 3 tanks. For removal of Inert Gas Soot, a 3 - 10 % solution should be used.
Direct Injection Method:
Inject 1 - 3 % of RXSOL 202 directly into the tank washing system. The recommended cleaning temperature is 80° C. When com-pleted rinse thoroughly with water.
Tank Rinsing:
In many cases an after treatment with Rxsol Metal Clean Bright is recommended for the removal of white lime deposits originating from sea water, residues out of the cargo or the combination of caustic with high tempera-tures. Inject 0,5 % Rxsol Metal Clean Bright directly into the tank washing system. Wash for approx. 20 - 30 minutes, at least 1 cycle. The recommended temperature is > 70 °C. Finally wash the tanks thoroughly with cold fresh water.
Boiler Cleaning:
Prior to acid cleaning of steam boilers which are contaminated with oil and grease or when silicates/calcium sulfates are present it is advised to first perform a boil out operation with RXSOL 202 . Fill the boiler with a 5 - 10 % solution of RXSOL 202 in water. Depending on the degree of contamination allow this solution to circulate for 12 to 24 hours at a temperature of 80 °C. After this boil out operation, completely drain the hot cleaning liquid and rinse the boiler intensively with cold water.
Cargo Hold Cleaning:
RXSOL 202 is used to clean cargo holds after carrying cargoes such as pet coke-, coal-, and mineral oil residues. After sweeping and demucking apply RXSOL 202 in a 10 - 50 % solution depend-ing on the contamination. Let the product soak for 30 minutes making sure not to let the solution dry on the surface. Then spray off with water.
Characteristics and notes
Future & Benefit :
- Eco-friendly.
- Biodegradable.
- Extreme powerful.
- Non flammable.
Safety and SDS
Read the safety data sheet before handling. Wear suitable gloves and eye protection.
View safety data sheet
| Product Name | RXSOL 202 |
| Product Type | RXSOL-20-2073-210 |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333/ 5555 / 9999 / 27611360 / 27815540 |
| Fax | +91 22 2781 1318 :::AOH :0091 9322594669 |
| rxsolchemicals@gmail.com |
Ingredient Cas. No. %
Potassium Hydroxide 1310-56-3 >5%
EFFECTS OF OVER EXPOSURE:
INHALATION : Irritant to mucous membranes.
INGESTION : Corrosive to mouth, throat, mucous membranes.
EYE CONTACT : Irritant to eyes.
SKIN CONTACT: Irritant to skin.
FOLLOW STANDARD FIRST AID PROCEDURES
SWALLOWING : Do not induce vomiting. Get medical attention.
SKIN CONTACT: Wash with water. Contact physician if irritation persists.
EYE CONTACT : Flush with running water. Consult with physician.
INHALATION : Remove to fresh air and get medical attention
FLASH POINT & METHOD USED: N/A
FLAMMABLE LIMITS:
NFPA RATING: N/A
HMIS RATING: HEALTH: 1 FIRE: 0 REACTIVITY:0
SPECIAL FIRE FIGHTING PROCEDURES AND PRECAUTIONS: None
UNUSUAL FIRE AND EXPLOSION HAZARDS: None
ENVIRONMENTAL PRECAUTIONS: Use absorbents on large spills.
SPILL OR LEAK PRECAUTIONS: Keep containers closed.
WASTE DISPOSAL: In accordance with federal, state and local laws.
No special precautions.
CONTROL MEASURES: If spilled, hose down with water, use absorbent material.
RESPIRATORY PROTECTION: Not required under normal use.
PROTECTIVE CLOTHING: Recommended.
EYE PROTECTION: Goggles and full face shield.
PEL: NO OSHA PEL TLV: NO ACGIH TLV
| BOILING POINT | : | N/D |
| MELTING POINT | : | N/A |
| VAPOR PRESSURE | : | N/A |
| SPECIFIC GRAVITY | : | 1.17 (Water = 1) |
| SOLUBILITY IN WATER | : | COMPLETE |
| APPEARANCE AND COLOR | : | GREEN, CLEAR LIQUID |
| pH | : | 13 |
| pH (5%) | : | 12.2 |
STABILITY: Stable
HAZARDOUS POLYMERIZATION: Will not occur
MATERIALS TO AVOID: Strong acids
HAZARDOUS DECOMPOSITION PRODUCTS: None
CONDITIONS TO AVOID:
Toxicological information
- No experimental data available
Inhalation
- Can cause damage to the respiratory system
Contact with skin
- Causes severe burns
Contact with eyes
- Causes severe burns
Ingestion
- The ingestion of significant quantities may cause burning sensation
Ecotoxicity
- This product for use as tank cleaning agent by chemical tankers.
Mobility
- Completely soluble in water
Persistence and Biodegradability
- Its main ingredients will either dissolve rapidly and dissociate in water or are readily/inherently
biodegradable.
Bioaccumulation Potential
- Bioaccumulation of the components in this product is insignificant.
- Disposal should be in accordance with local, state or national legislation
DOT SHIPPING NAME: Cleaning compound.
HAZARD CLASS: N/A
DOT CLASSIFICATION: Class 55
DOT PROPER SHIPPING NAME:
OTHER REGULATORY REQUIREMENTS: None
The data given here only applies when product used for proper application(s). The product is not sold as suitable for other applications - usage
in such may cause risks not mentioned in this sheet. Do not use for other application(s) without seeking advice from manufacturer. The stated
MSDS is reliable to the best of the company’s knowledge and believed accurate as of the date indicated. However, no representation, warranty
or guarantee of any kind, expressed or implied, is made as to its accuracy reliability or completeness and we assume no responsibility for any
loss, damage or expense, direct or consequential, arising out of use. It is the user’s responsibility to satisfy himself as to the suitableness and
completeness of such information for his own particular use.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
Availability
RXSOL 202 manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai, Sharjah, UAE, Gulf, Middle East, Muscat Oman, Kenya Africa. Get the best quality of RXSOL 202 at a competitive price from us. We have ready stock of RXSOL 202 in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.
