|
Product Name
|
Argon Gas (Pure)
|
|
Product Type
|
RXSOL-66-6604-010
|
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Branch : Kandla , Hazira, Mumbai. Chenna, Vizag, Kolkata, UAE, OMAN & KENYA
|
Phone |
+91 22 20871200 -1400 |
|
Fax |
+91 22 20871500 :::AOH :0091 9821214367 |
|
Email |
rxsolchemicals@gmail.com |
|
Website |
www.rxmarine.com/ |
|
CAS NO. |
Gas Component |
Percentage |
|
7440-37-1 |
Argon |
> 99 |
|
Hazard Identification |
Simple Asphyxiant _ Thise Product does not contain oxygen and may cause asphyxia if release in a confined area. maintan oxygen levels above 19.5% Non - flammable. |
|
Simple Asphyxiant |
This Product does not contain oxygen and may cause asphyxia if release in a confined area. maintan oxygen levels above 19.5% Non - flammable. |
|
WHIMIS Symbol |
A - Compressed Gas. |
|
NFPA Ratings |
|
|
Health |
= 0 (Blue) |
|
Fire |
= 0 (Red) |
|
Reactivity |
= 0 (Yellow) |
|
Specific Hazard |
= SA |
|
After inhalation |
Supply fresh air ; consult doctor in case of complaints. |
|
After Skin Contact |
Generally the product does not irritate. |
|
After Eye Contact |
Rinse opened eye for at least 15 minuts under running water, Then consult a doctor. |
|
After Swallowing |
Not applicable. |
|
Suiteble extinguishing agents |
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
|
|
Protective equipment |
Wear self contained respiratory protective. |
|
Person-related saftety precautions |
Wear protective equipment. Keep unprotecated persons away.Ensure adequate ventilation. Stop leak -only if posible to do so without risk. |
|
Measures for enviromental protection |
Prevent seepage into sewage system, work pits and/or cellars. |
|
Mesure fof cleaning /collecting |
Ensure adequate ventilation. |
|
Additional information |
No dangerous substance are releaed. |
|
Electrical classification |
Non hazadous.These Mixture are non corrosive and be used with any common structural material.Use only in well- ventilatd areas. Valve protection caps must remain in place unless container is secured with valve outlet piped to use point .Do not drag, slide or roll cylinders. Use a suitable hand truck for cylinder movement. Use a pressure reducing regulator when connecting cylinder to lower pressure (<3000 psig ) piping or system.Do not heat cylinder by any means to increse the discharge rate of product from the cylinder. Use a check valve to trap in the discharge line to prevent hazardous back flow into the system.Protecty cylinders from physical damage .store in th cool, dry well - ventilated area away from heavily trafficked areas and emergency exits. Do not allow the temperature where cylinders are stored to exceed 125°F (52°C).cylinders should be stored upright and firmly secured to prevent falling or being knocked over.Full and empty cylinders should be segregated. Use a " first in- first out " inventory system to prevent full cylinder from being store for excessive periods of time.
|
|
Additional information abouter design of technical system |
Adequate local ventilation. Safety showers and eyewash stations should be nearby . |
|
Exposure Limits |
|
|
Ingredingt |
Volume% |
PER OSHA |
|
Argon |
100% |
Simple asphyxiant |
|
General protective and hygienic measures |
Protective clothing should be kept free of and grease PPE should be inspected and maintained regularly to retain its effectiveness. |
|
Breathing equipment |
Use atmosphere - supplying respirators (eg. supplied - air. demand, pressure- demand,or continuous - flow or self contained breathing apparatus: demand or pressure -ndemand or combination supplied -air with auxiliary self contained air supply atmosphere supplying respiractor) in case of insufficient ventilation. |
|
Protective Gloves |
The selection of the suitable gloves does not only depend on the material ,but also on futher marks of quality and varies from manufacturer to manufacture. |
|
Eye protection |
Safety Glasses. |
|
Physical satate ( gas , liquid, soild) |
Gas |
|
Odour |
Odourless |
|
Colour |
Colourless |
|
Odour Threshould |
Not Applicable |
|
Vapour Pressure |
Not Available |
|
Vapour density (Air= 1) |
1.38 |
|
Evaporation point |
Not Available |
|
Boiling Point |
302.6°F -185.9°C |
|
Freezing Point |
308.9°F-189.4°C |
|
pH |
Not Available |
|
Applicable Specufuc gravity |
Not Available |
|
Oil / Water partition coefficient |
Not Available |
|
Solubilit (H2O) |
Slight |
|
Thermal decomposition / condition to be avoided |
No decomposition if uses according to specification. |
|
Dangerous reaction |
No dangerous reaction known. |
|
Dangerous Product of decomposition |
No dangerous reaction known. |
|
Acute Toxicity |
LD/LC50 values that are relevant for classification:LC50>5000ppm |
|
Primary irritant effect |
On the skin : No irritating effect .On the eye : No irritating effect .Sensitization : No sensitizing effict known . |
|
Addition toxicological infomation |
The product is not subject to classification according to internally approved calculation method for prepration :When used and handled according to specification, the prouduct does not have any harmful effect according according to our experience and the information provided to us. |
|
Generally no hazards for water. |
|
Product |
Unused product should be returned to vendor. |
|
Residual Pressure |
Do not attempt to dispose of residual waste or unfused quantity. |
|
Cylinder Identification |
Return ib the shipping container properly labeled, with valve protection caps, with valve outlet plug and proerly secured. |
|
Hzard |
2-2 non-flammable/toxic |
|
Identificataion number |
UN1006 . |
|
Proper shipping name |
Argon, Compressed Gas. |
|
Other transport information |
Avoid transport on vehicles where the load space is not separated from the driver's compartment. Ensure vehicle driver is aware of the potential hazards of the load and knows what to do in the event of an accident or an emergency. Before transporting product containers ensuer that they are firmly secured and: cylinder valve is closed and not leaking. valve outlet cap nut or plug (where provided) is correctly Fitted.valve protection device (where provided) is correctly fitted. there is adequate ventilation.Compliance with applicable regulations. |
|
DMC technical Guldelines |
ETG43 SARA TITLE III NOTIFICATION & INFORMATION SARA TITLE III -HAZARD CLASSES |
|
Actule health Hazard |
Sudden Release of pressure Hazard |
|
Product related hazard information |
Observe the general safety regulation when handling chemical. the product is not subject to identification regulations according to directives on hazarous materials .The product was classofication in accordance with the hazard criteria of the Canadian Controlled Products Regulation ( CPR) and the MSDS containts all the information required by the CPR. |
|
Safety phrases |
Keep in a cool place. |
|
Other Informatiom |
Compresses gas cylinders shall not be refilled without the express wrtten permission of the owner . Shipment of a compressed gass cylinder which has not been filled by the owner or with his / her (written) consent is a violation of traspotation regulation.Thise Information is based on our present knowledge However this shall not constitute a guarantee for any specific produt features and shall not establish a legally valid cotractual relatoinship Please refer to the section 3 for NFPA and HMIS Hazard codes.
DISCLAIMER OF EXPESSED AND IMPLIED WARRANTIES .Although reasonable care has been taken in the prepration of this Document, We extend no warranties and make no representation as to the accurancy or completeness of the information contained herein and assume no responsbility regarding the suitability of this information for the users intended purposes or for the consequences of its use .Each individual shoud make a determaination as to the sutabilility of the information for their particular.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
|
