Your shopping cart is empty.
Product Code: RXSOL-81-8169-025
Characteristic and Property:
| Physical Appearance | Light brown solid 100 Mesh Particale, free from visible impurities |
| Solubility of 10g of the Material in 1 liter of HSD Oil at 24 ± 2 °C | clear solution |
| Melting Point, °C | 150 (Minimum). |
| Specific Gravity | 1.05 |
| Flash Point |
>298°C |
Spurt Loss of Conventional Water :
Base Gel (Gelling Agent Grade 11 in 1% KC1, having 50-55 cP Viscosity at 511 sec-' shear rate) on treatment with 10 g / litre of Sample and subjecting it to a pressure of 1000 psi at 24 ± 2 °C, ml : 50(Maximum).
Product Code: RXSOL-81-8170-210
Product Code: RXSOL-60-6023-100
Product Details
| Alternative names |
n,n-Dimethylformamide, n-Formyldimethylamine |
| Molecular formula | C3H7ON |
| Molecular weight | 73.09 |
| Density | 0.945g/mL |
| CAS number | 68-12-2 |
| Appearance Form | liquid, clear |
DMF is specially purified and tested to the highest specifications to ensure the integrity of your data, maximize sensitivity in your assay and to prolong the life of your equipment.
Specifications DMF.
| Particulates | Free from particulate matter |
| Purity | > 99.5% |
| Water content | < 0.1% |
| Peroxides | No peroxides detected |
| Tollen’s test | No aldehydes detected |
| Ninhydrin positives A570 | < 0.05 above blank |
| UV cutoff | < 270nm |
N,N-Dimethylformamide CAS No. 68-12-2
Dimethylformamide (DMF) is a clear, colorless, hygroscopic liquid with a slight amine odor. The solvent properties of DMF are particularly attractive because of the high dielectric constant, the aprotic nature of the solvent, its wide liquid range and low volatility.
Product Code: RXSOL-19-1051-005
Product Code: RXSOL-60-6014-400
SPECIFICATION FOR SILICA GEL INDICATING (BLUE) / NON INDICATING (WHITE):
| Loss on drying : | Not more that 5% mass |
| Absorption Capacity : | 27% min on the basis of mass |
| PH : | 3.5 to 8. |
| Chlorides : | 0.05% by mass max |
| Cobalt (as CoCl2) : | 0.4 by mass max |
| Ammonium compounds (as NaH3): | 0.5% by mass max |
| Sulphates (Na2SO4) : | 0.5% by mass max |
| Packing: |
25 / 50 kgs M S drum (Smaller packing available). |
Product Code: RXSOL-41-8884-025
Steel Test Reagent For 304/316 Molybdenum Test kit manufacturer and supplier.
IMPORTANT : After use replace the cap on the bottle. Rinse thoroughly the tested surface. Contains 9% of hydrochloric acid.
Strictly Avoid Contact with SKIN , EYE and any part of BODY.
Product Code: RXSOL-22-2202-035
It is highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver as an alternative to using hazardous acids for concrete removal. Back-Set is a one-of-a-kind formula.
RXSOL-22-2202-035 turned this vulnerability into an opportunity. "Back-Set" safely removes hardened concrete from a variety of difficult to clean surfaces. It break down the ionic bond in portland cement, releasing the cement from any surface to which it has adhered.
This liquid mixture specifically designed to deal with hard cases of cement cargo deposits or dry cement stains. Its proven advantage is the provision of immediate penetration and complete dissolution of cement, the result being a thorough cleaning.
Chemically Back-Set converts the positive ions in the hardened matrix into negative ions, which dissolves the cement into mud that can be rinsed away. Because it works chemically, rather than mechanically, Back-Set may be used to remove cured concrete, mortar, grout, and stucco from virtually any surface without harm.
1. Apply cement remover on cement, to loosen the bond between the cement and the surface.
2. Give Sufficient time of reaction will loose bond of cement completely.
3. Repeat the 1st step on the cement for at least an hour or two.
4. For hot climate avoid evaporation, reapply frequently to keep the area moist.
5. After the cement starts to loosen, scrub the area with either a brush, Scotch Brite pad or scouring pad.
6. If a small amount remains, reapply Cement dissolver chemical and allow it to set again.
7. Scrub again until all of the cement is removed.
8. Flush the area with water.
9. Neutralise and Wash the area with alkaline soap and water.
Product Code: RXSOL-19-1880-050
TECHNICAL SPECIFICATIONS :
| Appearance/nature | : Viscous Flowable Liquid |
| Colour | : Colourless to pale yellow |
| on APHA (20% aqueous solution), maximum | : Characteristic |
| Odour | : 500-234-8 |
| pH (1 % aqueous solution) | : 6.8-8.5 |
| Active Matter, % by mass minimum | : 68 |
| Molecular Weight | : 384 |
| Sulfate, % by mass as Na2SO4, maximum | : 1.5 |
| N.D.O.M.,% by mass(on 100% A.M.basis), max | : 3.0 |
| 1, 4 - Dioxane (on 100% A.M. basis), ppm, max | : 30 |
| Iron content as Fe, ppm, maximum | : 5 |
| Heavy metals as Pb, ppm, maximum | : 15 |
| Microbial count, TVC, cfu/ml | : < 10 |
Certificate of Analysis according to DIN 55350-18-4.2.2
| Sr.No | Characteristic / Method | Unit | Value | Lower Limit | Upper Limit |
| 1. | Appearance @25 °C 93000601 | Confirms | Transparent to yellowish Flowable Paste | ||
| 2. | Odour 93000701 | Confirms | Conform to STD | ||
| 3. | Active Ingredient (M.W.384) ISO 2271 | % | 69.2 | 69.00 | 70.00 |
| 4. | pH 3% Solution ISO 4316 | 7.2 | 7.00 | 9.00 | |
| 5. | Sodium Sulfate Method No. 920015-01 | % | 0.3 | 1.00 | |
| 6. | Unsulfated Matter Method No. 970064-02 | % | 2.4 | 2.80 | |
| 7. | Dioxane (as is) Method No 920021-01 | ppm | 21 | 30 | |
| 8. | Colour APHA (20% Sol. @25 °C) ISO 6271 | 16 | 25 | ||
| Packing / Production Date | |||||
| Expiry Date / Shelf Life | |||||
Product Code: RXSOL-81-8159-210
SPECIFICATIONS:
| Color: | Opaque white to yellow |
| Odor: | Sweet to Mild chemical odor Specific Gravity: 0.98 @25°C |
| Flash Point: | 200°F |
| pH (10%): | 5.63 |
| Solubility: | Water Dispersible |
Product Code: RXSOL-41-8925-025
| Appearance/Physical State: | Clear Liquid |
| Vapor Pressure: | N/D |
| Boiling Point: | 212°F |
| Density: | 8.8 lbs. /gal. |
| Solubility in Water: | Soluble |
| Odor: | Citrus scent |
| Vapor Density: | N/D |
|
Freezing Point: |
N/D |
| Concentrate pH: | 12.4 - 12.8 |
|
RTU pH: |
10.7 - 11.3 |
Product Code: RXSOL-41-8661-025
Product Code: RXSOL-16-3036-025
Ultrasonic cleaning solutions can be essential when using an ultrasonic cleaner to achieve your desired results. RXSOL stocks a range of solutions which will cater for a wide range cleaning needs. Following are the cleaning solutions provided by us.
RXSOL-16-3006-025: It removes oil, removes rust and conditions the surface favorable to the adhesion of paint. It does all these three functions simultaneously. It can be used very effectively on all metals, non-metals, alloys, castings, polymers, plastics, rubber parts, polyester screens nylons, including various components, parts and assemblies of the Textile, Engineering and Automobile Industry. It is a versatile general purpose cleaner. It is very safe to use on all metals& Non-metals.
