Your shopping cart is empty.
RXSOL-16-1665-025 is a fluid cleaning and degreasing agent with a wide range of application. It can be used for practically all cleaning and degreasing purposes.
RXSOL-16-1665-025 cleans rapidly, thoroughly and extremely economically.
Use of RXSOL-16-1665-025 renders safety precautions superfluous.
RXSOL-16-1665-025 has these outstanding characteristics without exhibiting the
isadvantages of solvent cleaners.
RXSOL-16-1665-025 is non-flammable and free from caustic
This product is biologically degradable
RXSOL-16-1665-025 can be undercooled or overheated during storage but remains fully usable when returned to normal temperature.
PRODUCT PROPERTIES
APPEARANCE Clear Colourless Liquid
COMPATIBILITY METAL No known effect RUBBER May Swell
PACKAGING Order no.: Size 50 / 25 LTR RXSOL-18-1014-050
FIRSTAID &STORAGE:- Contact with skin can cause serous chemicals burns .Avoid contact with skin & eyes.Wear PVC gloves while handling. Do not take internally. Spl-ashes of the product or its solutions on the skin or clothing should washed immediately with cupious amount of water . If the eyes are affected should be washed with water for at least 15 minutes and seek medicals attention sought immediately. Keep drums tightly closed when not in use.
PROPERTIES:
Color ............................................................................ Milky White
Dilution ..............................Use as necessary , unless foam abides
Flash Point ............................................................................ None
Fragrance ................................................................Characteristic
pH ...................................................................................... 7.0 - 8.0
Packaging.........................................Case/4 - 1 US gallon (3.78 L)
PRECAUTIONS:
SAFETY:
Keep out of reach of children. For institutional and commercial use.
CAUTION:
Contains emulsifiers. May cause eye irritation. Avoid Contact with eyes. FIRST AID: If splashed on skin, wash with soap and water. If splashed in eyes, fl ush with large quantities of water. If swallowed, dilute with two glasses of water. Call a physician.
SPECIFICATION FOR SILICA GEL INDICATING (BLUE) / NON INDICATING (WHITE):
| Loss on drying : | Not more that 5% mass |
| Absorption Capacity : | 27% min on the basis of mass |
| PH : | 3.5 to 8. |
| Chlorides : | 0.05% by mass max |
| Cobalt (as CoCl2) : | 0.4 by mass max |
| Ammonium compounds (as NaH3): | 0.5% by mass max |
| Sulphates (Na2SO4) : | 0.5% by mass max |
| Packing: |
25 / 50 kgs M S drum (Smaller packing available). |
Steel Test Reagent For 304/316 Molybdenum Test kit manufacturer and supplier.
IMPORTANT : After use replace the cap on the bottle. Rinse thoroughly the tested surface. Contains 9% of hydrochloric acid.
Strictly Avoid Contact with SKIN , EYE and any part of BODY.
It is highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver as an alternative to using hazardous acids for concrete removal. Back-Set is a one-of-a-kind formula.
RXSOL-22-2202-035 turned this vulnerability into an opportunity. "Back-Set" safely removes hardened concrete from a variety of difficult to clean surfaces. It break down the ionic bond in portland cement, releasing the cement from any surface to which it has adhered.
This liquid mixture specifically designed to deal with hard cases of cement cargo deposits or dry cement stains. Its proven advantage is the provision of immediate penetration and complete dissolution of cement, the result being a thorough cleaning.
Chemically Back-Set converts the positive ions in the hardened matrix into negative ions, which dissolves the cement into mud that can be rinsed away. Because it works chemically, rather than mechanically, Back-Set may be used to remove cured concrete, mortar, grout, and stucco from virtually any surface without harm.
1. Apply cement remover on cement, to loosen the bond between the cement and the surface.
2. Give Sufficient time of reaction will loose bond of cement completely.
3. Repeat the 1st step on the cement for at least an hour or two.
4. For hot climate avoid evaporation, reapply frequently to keep the area moist.
5. After the cement starts to loosen, scrub the area with either a brush, Scotch Brite pad or scouring pad.
6. If a small amount remains, reapply Cement dissolver chemical and allow it to set again.
7. Scrub again until all of the cement is removed.
8. Flush the area with water.
9. Neutralise and Wash the area with alkaline soap and water.
TECHNICAL SPECIFICATIONS :
| Appearance/nature | : Viscous Flowable Liquid |
| Colour | : Colourless to pale yellow |
| on APHA (20% aqueous solution), maximum | : Characteristic |
| Odour | : 500-234-8 |
| pH (1 % aqueous solution) | : 6.8-8.5 |
| Active Matter, % by mass minimum | : 68 |
| Molecular Weight | : 384 |
| Sulfate, % by mass as Na2SO4, maximum | : 1.5 |
| N.D.O.M.,% by mass(on 100% A.M.basis), max | : 3.0 |
| 1, 4 - Dioxane (on 100% A.M. basis), ppm, max | : 30 |
| Iron content as Fe, ppm, maximum | : 5 |
| Heavy metals as Pb, ppm, maximum | : 15 |
| Microbial count, TVC, cfu/ml | : < 10 |
Certificate of Analysis according to DIN 55350-18-4.2.2
| Sr.No | Characteristic / Method | Unit | Value | Lower Limit | Upper Limit |
| 1. | Appearance @25 °C 93000601 | Confirms | Transparent to yellowish Flowable Paste | ||
| 2. | Odour 93000701 | Confirms | Conform to STD | ||
| 3. | Active Ingredient (M.W.384) ISO 2271 | % | 69.2 | 69.00 | 70.00 |
| 4. | pH 3% Solution ISO 4316 | 7.2 | 7.00 | 9.00 | |
| 5. | Sodium Sulfate Method No. 920015-01 | % | 0.3 | 1.00 | |
| 6. | Unsulfated Matter Method No. 970064-02 | % | 2.4 | 2.80 | |
| 7. | Dioxane (as is) Method No 920021-01 | ppm | 21 | 30 | |
| 8. | Colour APHA (20% Sol. @25 °C) ISO 6271 | 16 | 25 | ||
| Packing / Production Date | |||||
| Expiry Date / Shelf Life | |||||
SPECIFICATIONS:
| Color: | Opaque white to yellow |
| Odor: | Sweet to Mild chemical odor Specific Gravity: 0.98 @25°C |
| Flash Point: | 200°F |
| pH (10%): | 5.63 |
| Solubility: | Water Dispersible |
| Appearance/Physical State: | Clear Liquid |
| Vapor Pressure: | N/D |
| Boiling Point: | 212°F |
| Density: | 8.8 lbs. /gal. |
| Solubility in Water: | Soluble |
| Odor: | Citrus scent |
| Vapor Density: | N/D |
|
Freezing Point: |
N/D |
| Concentrate pH: | 12.4 - 12.8 |
|
RTU pH: |
10.7 - 11.3 |
Ultrasonic cleaning solutions can be essential when using an ultrasonic cleaner to achieve your desired results. RXSOL stocks a range of solutions which will cater for a wide range cleaning needs. Following are the cleaning solutions provided by us.
RXSOL-16-3006-025: It removes oil, removes rust and conditions the surface favorable to the adhesion of paint. It does all these three functions simultaneously. It can be used very effectively on all metals, non-metals, alloys, castings, polymers, plastics, rubber parts, polyester screens nylons, including various components, parts and assemblies of the Textile, Engineering and Automobile Industry. It is a versatile general purpose cleaner. It is very safe to use on all metals& Non-metals.
