IGS CLEANER
- Part number
- RXSOL-20-2098-210
- Category
- Tank Cleaner
- Brand
- RXSOL
Overview
Specifically formulated for the effective removal of Inert Gas Soot (IGS) in tanks. Also acts as MULTIPURPOSE CLEANER & DEODORIZER
Specialized and effective removal of Inert Gas Soot (IGS) in tanks removing mineral oils, petroleum products, vegetable and animal oils, fish oils, carbon deposits, dirt, grease and grime. Compatible with most painted surfaces and dries leaving a good shine.
IGS CLEANER (INERT GAS SOOT CLEANER) is a water-based alkaline tank cleaner and degreaser, spceially formulated for the effective removal of Inert Gas Soot (IGS) in tanks.
IGS CLEANER is developed for overcoming the limitations imposed by liquid caustic based cleaning compounds.Its non-caustic cleaning and degreasing action, ensures the soot removal, without harming the paint and the personnel using it. IGS CLEANER is highly concentrated, comprising the most powerful biodegradable detergents, surfactants and corrosion inhibitors.
IGS CLEANER is water based, non flammable, biodegradable
IGS CLEANER (INERT GAS SOOT) EXTREMELY EFFECTIVE INERT GAS SOOT CLEANER,MULTIPURPOSE CLEANER & DEODORIZER
Applications
IGS CLEANER can be used to clean for stainless steel and epoxy coated tanks from Inert Gas Soot. Diluted, it removes most contaminations. IGS CLEANER can also be used as a deodorizing wash in all applications.
Suitable for epoxy, but not for zinc silicate coatings. In this case, use it diluted, and only after thorough testing of the product and surface interaction.
Dosage and directions
USE AND DOSING :
Instructions are based on experience and are meant only as a guide since circumstances for each tank cleaning operation vary. They are not intended to interfere with the judgment of the vessel’s responsible personnel.
Precleaning tanks with high pressure warm water is highly recommended since large deposits of oil or other residues in the tank must be removed to ensure an effective cleaning operation. Note that all cleaning chemicals have reduced effect with seawater. Prior to use of any chemicals, make sure the tanks and lines
are well stripped and drained.
Do not overheat as this may change the characteristics of the cargo and in some cases burn the cargo on the bulkhead. Carefully read the cargo specification.
Especially for zinc, since it is porous, a prolonged pre-cleaning with lower temperatures is highly recommended before chemicals are used on such lining.
Characteristics and notes
USE AND DOSING (continued) :
solution through the tank washing system for a period of at least two hours per machine drop, with a cleaning time of 4 hours per tank usually being sufficient.
A minimum temperature of 70°C is recommended, since the cleaning ability is enhanced and the cleaning time shortened. However, the solution may be used at ambient temperature.
Tip: Do not use the entire quantity of IGS CLEANER in one solution for all tanks to be cleaned. Keep a few drums for boosting the solution’s cleaning efficiency for the last few tanks.
When recirculation is completed, wash down with water, using the maximum pressure available. In the case that stains remain on the surfaces, spot clean with undiluted IGS CLEANER directly on the stained area. Allow a reaction time of 30 minutes and then rinse with water. Do not leave the product to dry on bare coating.For persistent deposits, agitation by scrubbing will assist the cleaning operation. Heated water will increase the cleaning effect.
For general use, dilute appropriately,depending on the contamination and use conventional cleaning methods, such as brushing, scrubbing or spraying. Allow the product to act and then rinse with fresh water before drying.
PRODUCT PROPERTIES :
It is highly recommended to always test all cleaner solutions on a small area of tank coating, before full scale application.
Appearance : Odor
Density at 20°C: Flash Point
pH (undiluted): Solubility
Compatibility(concentrated)
Red liquid :Soft
1.05 ± 0.05 g/cm: None
13.0 ± 1.0
Soluble in water :Incompatible with aluminum, zinc, tin and their alloys
Extremely effective for removing inert gas soot.
• Effective cleaning of stainless steel and epoxy coated tanks.
• Strong deodorizer.
• Safer to use, substituting liquid austic based cleaners.
• Heavy duty, water-based leaner.
• Versatile for multipurpose leaning.
• Cost effective: dilute for mostcleaning needs.
• Contains neither hydrocarbonsolvents, nor nonyl phenol ethoxylates or other estrogenic compounds.
• Non-flammable & non-toxic.
• Bio-degradable, minimizing environmental concerns.
Inert Gas Soot.
Mineral oils, petroleum products,drying or semi-drying oils, carbon deposits, dirt, grease and grime.
Odor problems.
APPLICABLE AREAS:
- Cargo tanks and bulkheads.
- General cleaning.
Safety and SDS
Read the safety data sheet before handling. Wear suitable gloves and eye protection.
View safety data sheet
| Product Name | IGS CLEANER Part No. - RXSOL-20-2098-210 |
| Product Type | Alkaline Tank & Industrial cleaner |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 27815540-43 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| rxsolchemicals@gmail.com |
SURFACTANT ( ANIONIC & NON-IONIC ) , LAB derivative , Sodium hydroxide Strong alkaline cleaner Declaration according recommendation
89/542/EEG..
|
Environmental Hazards |
None |
|
Human Health Hazards |
Moderates |
R 35:Causes skin burning effects
|
Inhalatin |
Harmful,. supply or remove to fresh air and seek medical advice attention. |
|
Skin Contact |
Rinse with running water and soap. Skin care. Remove contaminated clothes. |
|
Eye Contact |
Flush with running water for at least 15 minutes Immediately . |
|
Ingestion |
Vomiting is dangerous , seek medical attention. |
Non Combustible Porduct
|
Suitable |
N.A. can use foam dry Co2 , water-spray. |
|
Not suitable |
Not applicable |
|
Special |
Not applicable |
|
Protection of fire Fighter |
Not applicable |
Special protective equipment for fire-fighters: Wear protective equipment.
|
Enviromentel Precaution |
Direct flow into drainage system, surface or ground water is prohibited. |
|
Cleaning Method |
Flush Spill Area with Water and remove with liquid-absorbing material like foam sand,sawdust etc.. |
|
Condition to Avoid |
Non flammable but avoid direct heating |
|
Materials to Avoid |
Do not subject to Acidic / Oxidizing Agents |
|
Handling |
Keep Container Tightly Closed |
Note:Eyewash facilities require at workplace The product causes corrosion on skin and mucous membranes Pl. Note that In case of discharge of acidic or alkaline products into the sewerage system the pH must be in the range of 6-10 since higher or lower pH values may damage the sewerage system or impair biological dosage treatment plants. So that for maintaining pH we have to add acidic / basic medium neutaliser . For example if pH is less than 6 basic neutraliser is required and if pH is more than 10 acidic nature neutraliser is required. For details of any guideline pl. Visit our technical website www.rxmarine.com
Dilute in water (always use plastic jar and RXSOL should be added to water never add water to RXSOL.)
Personal protection :
|
Respiratory System Protection |
Approved respirator must be worn when spraying |
|
Eye Protection |
Cear eye protection (on possibility of contact ) |
|
Hand protection |
Cear PVC chemical resistance protective glove |
Product Properties:
|
Appearance |
Slight Yellow - clear liquid |
|
Density |
In g/cm3 at 20°C: 1.21 |
|
Compatibility |
|
|
Metal |
No known effect |
|
Rubber |
No known effect |
|
pH |
Alkaline ( 13 ) |
|
Flash point |
Not Applicable |
|
Solubility |
100% soluble in water |
|
Packaging |
Size (in Litres)220 Ltrs |
|
Hazardous Decomposition Products |
Do not occur if stored and used as directed. n FIRE combustion CO, CO2 , NH3 , SOX etc hazardous gas produced |
NOTE : Avoid Contact With Acid
Comment - Not applicable , 100% Soluble in water
95 % added surfactants are biodegradable as per by international regulation .This material must be disposed with local national regulations.
As per guide line of local rules and regulation and before disposal and neutralization pl. refer 07 article.
| Proper Shipping Name | ||||
| UN | ||||
| Proper Shipping Name |
Sodium hydroxide, solution |
|||
| UNNo. | 1824 | |||
| Hazard Class | 8 | PackingGroup | II | |
| Road/Rail(ADR/RID) | ||||
| Proper Shipping Name |
Sodium hydroxide, solution |
|||
| ADR UN No. | 1824 | |||
| ADR Hazard Class | 8 | Tremcard |
80S1824 |
|
|
Sea(IMDG) |
||||
| Proper Shipping Name |
Sodium hydroxide, solution |
|||
| IMDG UN No. | 1824 | |||
| IMDG Hazard Class. | 8 | IMDG Pack Group. | II | |
| IMDG EmS | F-A, S-A | IMDG subrisk |
N/A |
|
| IMDG Labels |
8 |
IMDG Flash point |
N/A |
|
|
Air(ICAO/IATA) |
||||
| Proper Shipping Name |
Sodium hydroxide, solution |
|||
| ICAO Un No. | 1824 | |||
| ICAO Hazard Class | 8 | ICAO Packing Group. | II | |
| ICAO subrisk |
N/A |
ICAO Labels |
8, CAO |
|
| ICAO Flashpoint | N/A | |||
|
DOT/ CFR (US Department of Transportation) |
||||
| DOT Proper Shipping Name |
Sodium hydroxide, solution |
|||
| Hazardous Material |
Sodium hydroxide |
|||
| Hazard Class | 8 | Identification Number | UN 1824 | |
| Product RQ (lbs) | 3640 | DOT subrisk | N/A | |
| DOT Labels | 8 | DOTFlashpoint |
N/A |
|
Classification and labelling according to Chemicals Hazard Information and Packaging Regulations (CHIP). Symbols of danger :- C Corrosive
|
R phrases |
R 35 : Causes severe burns |
|
S-phrases |
S2: Keep out of reach of children S26 :In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S28 : After contact with skin, wash immediately with plenty of water. S37/39 : Wear suitable gloves and eye/face protection. |
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our product from the point of view of safety requirements and is not intended to guarantee any particular properties
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
Availability
IGS CLEANER manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai UAE, Muscat Oman, Kenya Africa. Get the best quality of IGS CLEANER at a competitive price from us. We have ready stock of IGS CLEANER in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.
