Power Plant / Heavy Industries
MoldGuard Algae Mold Control
- Part number
- RXSOL-37-8719-025
- Category
- Power Plant / Heavy Industries
- Brand
- RXSOL
Overview
Effectively Cleans and control of mold acts as Anti Micro Bial Product Its highly concentrated advanced formula makes it toughest mold cleaning agent. MoldGuard Algae Mold Control effectively results in moisture and damp area.
Applications
MoldGuard Algae Mold Control is resulting transparent invisible result after dries on surfaces. And effectively prohibits the growth of mold and fungal algae. Its antimicrobial formula makes it popular mold releasing treatment chemicals.
USES OF MoldGuard Algae Mold Control
- Mold remediation in homes, businesses and institutions
- Mold prevention following flooding or water damage cleanup
- Pre-treatment of building materials for mold resistance
PREVENTATIVE TREATMENT
To inhibit the growth of mold and mildew on surfaces:
- Apply MoldGuard Algae Mold Control on area until evenly wet.
- To promote drying and to avoid residue marks, use a clean cloth or paper towel to wipe off excess wetness.
- Allow treated surfaces to dry completely.
Dosage and directions
MoldGuard Algae Mold Control is most commonly used in basements, bathrooms and laundry rooms and dampness area. MoldGuard Algae Mold Control can be apply by spraying as we as mopping method. Its application is very simple and easy.
Characteristics and notes
REMEDIAL TREATMENT SMALL AREAS
Areas of visible growth of less than 30 square feet (the area of a single wall panel) can normally be remediated without elaborate procedures. When these areas are identified, apply MoldGuard Algae Mold Control to retard growth and spread of fungal spores and other contaminates until the area can be thoroughly cleaned and remediated. If growth is on ceiling tiles or other such easily removable items of nominal value, remove them and seal them in a plastic bag and dispose with normal trash. If the surface is not easily replaceable: MoldGuard Algae Mold Control–
Application Instructions
- Clean contaminated area to remove surface soil. For best results, and to avoid possible interference from other chemicals, use MoldGuard Algae Mold Control for initial cleaning. Use a cloth, cleaning pad or brush suitable to the durability of the surface being cleaned. Remove as much dirt and visible mold as possible.
- Apply MoldGuard Algae Mold Control on cleaned area until evenly wet.
- To promote drying and to avoid residue marks, use a clean cloth or paper towel to wipe off excess wetness.
- Allow treated surfaces to dry completely. Refer to the Personal Protection Equipment Requirements for Applicators section for the appropriate PPE to wear.
MoldGuard Algae Mold Control is suitable for use on most surfaces. If in doubt, perform a test on a small, inconspicuous section. Materials vulnerable to water marks should be wiped immediately after contact with MoldGuard Algae Mold Control. Over-application may in some cases result in residue formation, which can be easily wiped away with a MoldGuard Algae Mold Control-dampened cloth. MoldGuard Algae Mold Control can be applied by hand-spray, paintbrush, roller, immersion, airless sprayer or pressure fogger (approximately one gallon of product should treat a 400 sq. ft. room with a fogger). To maintain protection against re-growth, do not rinse or wash surfaces after treatment. Reapplication of MoldGuard Algae Mold Control may be required if surfaces are washed or painted or are otherwise directly exposed to water. Ready to use – do not dilute. MoldGuard Algae Mold Control must come in direct contact with mold to be effective.
1 ltr for 10 sq mtr
Safety and SDS
Read the safety data sheet before handling. Wear suitable gloves and eye protection.
View safety data sheet
| Product Name |
MoldGuard Algae Mold Control |
| Product Type | RXSOL-37-8719-025 |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Points: Mumbai, Kandla, Kolkata, Visakhapatnam, Chennai, Fujairah UAE, Muscat Oman, Kenya, Canada
| Phone | +91 22 27815541 / 42 |
| AOH | 0091 9322594669 |
| rxsolchemicals@gmail.com |
Proprietary mixture of food-grade Tri sodium phophate, inorganic salts and purified water.
|
SARA 313 Substances: NONE Organic Compounds: NONE Clear Air Act Sec. 122 Substances: NONE VOCs: NONE |
Known or Suspected Carcinogens: NONE Alcohols: NONE Ammonias: NONE Chlorines: NONE |
All ingredients are listed on the TSCA Chemical Substance Inventory.
Hazard Rating (HMIS/WHMIS)
|
Health |
0 |
|
Fire |
0 |
|
Reactivity |
0 |
|
Special |
0 |
| Routes of entry | Dermal most likely |
| Acute health hazards: | None known |
| Chronic health hazards | None known |
Carcinogens:No ingredients are listed by OSHA, IARC, or NTP as known or suspected carcinogens
If irritation occurs, rinse area thoroughly with water. If swallowed, drink 1 glass of water.
Flashpoint: N/A
Extinguishing Media: NON-FLAMMABLE
Unusual Fire and Explosion Hazards: NON-FLAMMABLE
Special Fire Fighting Procedures: NONE
Recover usable material if possible. Non-recoverable material can be disposed of in accordance with standard wastewater treatment methods
Store containers between 39°F (4°C) and 100°F (38°C). If product freezes, thaw and mix thoroughly. No special handling requirements. Keep out of reach of children.
No special controls, ventilation, or personal protective equipment is required in handling the product. However, to avoid applicator exposure to mold or mold spores during use, see label for "PERSONAL PROTECTION EQUIPMENT REQUIREMENTS FOR APPLICATORS".
|
Appearance: Clear liquid |
Odor: Odorless |
|
Boiling Range: 212°F / 100°C |
Weight/US Gal: 8.5 lbs (3.9 kg) |
|
Evaporation Rate: Slower than ether |
Vapor Density: Heavier than air |
|
pH: 11.1 – 11.5 |
|
Stability: Stable
Reactivity: Non-reactive
Hazardous polymerization: Will not occur
Hazardous decomposition products: None
Oral: No known hazards in normal use. LD50 >5000 mg/kg
Dermal: No known hazards in normal use. LD50 >5050 mg/kg
Eye Irritation: No known hazards in normal use. Non-irritating
Skin Irritation: No known hazards in normal use. Non-irritating
Inhalation: No known hazards in normal use. LC50 >2.28 mg/L
Sensitization: No known hazards in normal use. Not a sensitizer
No special disposal considerations beyond accordance with federal, provincial, or local wastewater regulations. Recycle empty container.
DOT SHIPPING DESCRIPTION: Not Regulated
DOT HAZARD CLASS: N/A
UN NUMBER: N/A
DOT PACKING GROUP: N/A
DOT PRIMARY/SECONDARY LABEL: N/A
DOT PRIMARY/SECONDARY PLACARD: N/A
DOT EMERGENCY RESPONSE GUIDE #: N/A
Occupational Health and Safety Regulations:
WHMIS Class: Class D Division 2B
OSHA & WHMIS: MSDS prepared pursuant to the Hazard Communication Standard ( CFR29.1920.1200) and Canadian WHMIS regulations
SARA – Section 313 (Toxic Chemical Release Reporting) 40 CFR 372 : None of these ingredients are listed
CERCLA – Section 102 (Reportable Quantity) 40 CFR 302 : None of these ingredients are listed
RCRA 40 CFR 261 (Subpart D) : None of these ingredients are listed
CLEAN WATER ACT – Section 311 ( Reportable Qty) 40 CFR 116: None of these ingredients are listed
CLEAN AIR ACT – Section 312 ( List of Hazardous Pollutants) 40 CFR 63 (Subpart C) : None of these ingredients are listed
National Pollutant Release Inventory Toxic Substances Control Act (TSCA): None of these ingredients are listed
No special disposal considerations beyond accordance with federal, provincial, or local wastewater regulations. Recycle empty container.
The information set forth herein is believed to be accurate. RX MARINE INTERNATIONAL. makes no warranty, expressed or implied, regarding the accuracy of the data or the results to be obtained from the use thereof. The information is supplied solely for your information and consideration, and RX MARINE INTERNATIONAL. assumes no responsibility for use or reliance thereon. It is the responsibility of the user of RX MARINE INTERNATIONAL. products to comply with all applicable federal, state and local laws and regulations.
RX MARINE INTERNATIONAL. warrants its products to be free from defects in material and workmanship. RX MARINE INTERNATIONAL.’s liability on any claim of any kind, including claims based upon RX MARINE INTERNATIONALnegligence or strict liability, for any loss or damage arising out of, connected with, or resulting from the use of the products, shall in no case exceed the purchase price of the products or part thereof which give rise to the claim. In no event shall RX MARINE INTERNATIONAL. be liable for consequential or incidental damages.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
Availability
MoldGuard Algae Mold Control manufacturer and supplier in Mumbai, Kandla, Chennai, Visakhapatnam, Kolkata, Fujairah, Dubai, Sharjah, Abudhabi, Muscat, Sohar, Oman, Kenya Africa, Canada
