|
Product Name |
TITANIUM METAL POWDER AR 150-200MESH |
|
Part Number |
RXSOL-60-6605-740 |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Branch : Kandla, Mumbai , Chennai, Vizag, Kolkata, UAE , OMAN , CANADA and KENYA
|
Phone |
+91 22 20871200 - 1400 |
|
Fax |
+91 22 27612100 :::AOH :0091 9821214367 |
|
Email |
rxsolchemicals@gmail.com |
|
Website |
www.rxmraine.comA |
|
Chemical Name |
CAS |
EC number |
Weight |
Formula |
|
Titanium |
7440-32-6 |
231-142-3 |
<= 100 % |
Ti |
|
Signal Word |
Danger |
|
Hazard Statements |
H228 Flammable solid. |
|
Precautionary statements |
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P240 Ground and bond container and receiving equipment. P241 Use explosion-proof electrical/ ventilating/ lighting/ equipment. P280 Wear protective gloves/ protective clothing/ eye protection/ face protection. P370 + P378 In case of fire: Use dry sand, dry chemical or alcohol-resistant foam to extinguish. |
|
Classification of the substance or mixture |
Not a hazardous substance or mixture according to Regulation (EC) No 1272/2008. |
|
Supplemental Hazard Statements |
None. |
|
Other hazards |
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher. |
|
General advice |
Show this material safety data sheet to the doctor in attendance. |
|
If inhaled |
After inhalation: fresh air. |
|
Eye Contact |
After eye contact: rinse out with plenty of water. Remove contact lenses. |
|
Swallowed |
After swallowing: make victim drink water (two glasses at most). Consult doctor if feeling unwell. |
|
Skin Contact |
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. |
|
Inhalation |
Remove patient to fresh air, keep warm and at rest and get medical assistance in necessary. |
|
Ingestion |
Rinse mouth with water. Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a doctor or Poison Control Center immediately. |
|
Most important symptoms and effects, both acute and delaye |
The most important known symptoms and effects are described in the labelling (see section 2.2) and/or in section 11 |
|
Indication of any immediate medical attention and special treatment needed |
No data available |
|
Flammability |
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide. |
|
Suitable extinguishing media |
Use approved class D extinguishers or smother with dry sand, dry ground limestone, or dry clay.Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. |
|
Unsuitable extinguishing media |
For this substance/mixture no limitations of extinguishing agents are given. |
|
Special hazards arising from the substance or mixture |
Titanium/titanium oxides Not combustible. Ambient fire may liberate hazardous vapours. |
|
Further information |
No data available |
Hazardous combustion
products |
Fire may cause the evolution of Sulphur oxides, nitrogen oxides. |
|
Advice for firefighters |
In the event of fire, wear self-contained breathing apparatus. |
|
Protective Equipment |
Use personal protective equipment. |
|
Specific Hazards Arising from the Chemical |
Oxides of phosphorus Sodium oxides Not combustible. Fire may cause evolution of: Oxides of phosphorus Ambient fire may liberate hazardous vapours. |
|
Personal precautions, protective equipment and emergency procedures |
Advice for non-emergency personnel: Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition. Evacuate the danger area, observe emergency procedures, consult an expert. For personal protection see section 8. |
|
Spillage |
Oxidizing material. Stop leak if without risk. Avoid contact with a combustible material (wood, paper, oil, clothing...). Keep substance damp using water spray. Do not touch spilled material. Prevent entry into sewers, basements or confined areas dike if needed. Eliminate all ignition sources. Call for assistance on disposal. |
|
Enviromental Precaution |
Do not let product enter drains. Risk of explosion. |
Methods and materials for
containment and cleaning |
Observe possible material restrictions (see sections 7 and 10). Take up dry. Dispose of properly. Clean up affected area. Avoid generation of dusts. |
|
Advice on protection against fire and explosion |
Keep away from open flames, hot surfaces and sources of ignition.Take precautionary measures against static discharge. |
|
Incompatible materials |
Keep away from alkalis, strong oxidizing agents and metals. Provide containment walls of adequate capacity to hold any accidental spills. |
|
Hygiene measures |
Change contaminated clothing. Wash hands after working with substance. For precautions see section 2.2. |
|
Precautions for safe handling |
For precautions see section 2.2. |
|
Storage conditions |
Tightly closed. Keep away from heat and sources of ignition. Handle and store under inert gas. Air and moisture sensitive. |
|
Storage class |
Storage class (TRGS 510): 4.1B: Flammable solid hazardous materials |
|
Specific end use(s) |
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated |
|
Advice on general occupational hygiene |
Advice on safe handling Observe label precautions. Change contaminated clothing. Wash hands after working with substance. |
|
Requirements for storage |
Keep in cool and store under shade. |
|
Exposure controls |
Appropriate engineering controls Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday. |
|
Control parameters |
Ingredients with workplace control parameters Contains no substances with occupational exposure limit values. |
|
Engineering Control |
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday. |
|
Eye/face protection |
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses |
|
Body Protection |
Flame retardant antistatic protective clothing. |
|
Skin protection |
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands. The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it. Protective gloves against thermal risks Full contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:Dermatril® (KCL 740 / Aldrich Z677272, Size M) Splash contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:Dermatril® (KCL 740 / Aldrich Z677272, Size M) data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail sales@kcl.de, test method: EN374 If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the EC approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario. |
|
Respiratory protection |
Required when dusts are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type P1 The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented. |
|
Other Protection Measure |
Handle in accordance with good industrial hygiene and safety practice. |
|
Control of environmental exposure |
Do not let product enter drains. Risk of explosion. |
Gloves Suit
|
Physical state |
Powder |
|
Colour |
No data available |
|
Odour |
No data available |
|
Odor Threshold |
No data available |
|
pH |
No data available |
|
Melting Point |
1.660 °C - lit. |
|
Boiling Point |
3.287 °C - lit. |
|
Flash Point |
No data available |
|
Evaporation Rate |
Not Applicable |
|
Flammability (solid, gas) |
No data available |
|
Explosive limits |
No Data Available |
|
Upper/lower flammability or explosive limits |
No data available |
|
Autoignition temperature |
No data available |
|
Decomposition temperature |
No data available |
|
Vapour pressure |
No data available |
|
Density |
4,5 g/mL at 25 °C - lit. |
|
Relative Density |
No data available |
|
Relative vapor density |
No data available |
|
Freezing point |
No data available |
|
Viscosity |
No data available |
|
Partition coefficient |
No data available |
|
Explosive properties |
No data available |
|
Solubility |
No data available |
|
Ignition temperature |
No information available. |
|
Particle characteristics |
No data available |
|
Reactivity |
No data available |
|
Stability |
The product is chemically stable under standard ambient conditions (room temperature) . |
|
Possibility of hazardous reactions |
Risk of ignition or formation of inflammable gases or vapours with: Risk of explosion with: Water Halogenated hydrocarbon nitrogen nitrile halides Oxidizing agents metallic salts carbon dioxide halogen oxides Oxygen nonmetals Nitric acid Potassium carbonate Violent reactions possible with: metallic oxides halogens halogen-halogen compounds |
|
Conditions to avoid |
No data available |
|
Incompatible materials |
No data available |
|
Hazardous decomposition products |
In the event of fire: see section 5 |
|
Acute toxicity |
Oral: No data available Inhalation: No data available Dermal: No data available |
|
Skin corrosion/irritation |
Remarks: Causes severe burns. Classified according to Regulation (EU) 1272/2008, Annex VI (Table 3.1/3.2) |
|
Serious eye damage/eye irritation |
Remarks: Causes serious eye damage. |
|
Respiratory or skin sensitization |
Maximization Test - Guinea pig Result: negative (OECD Test Guideline 406) |
|
Toxic Effects on Human |
May cause damage to the following organs: upper respiratory tract. Other Toxic Effects on Humans: Hazardous in case of skin contact (irritant, sensitizer), of ingestion, of inhalation (lung irritant, lung sensitizer). |
|
Carcinogenicity |
No data available |
|
Germ cell mutagenicity |
In vivo tests did not show mutagenic effects Test Type: In vitro mammalian cell gene mutation test Test system: mouse lymphoma cells Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 476 Result: Positive results were obtained in some in vitro tests. Test Type: Chromosome aberration test in vitro Test system: Human lymphocytes Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 473 Result: positive Test Type: In vivo micronucleus test Species: Mouse Cell type: Bone marrow Application Route: Intraperitoneal Method: OECD Test Guideline 474 Result: negative |
|
Reproductive toxicity |
No data available |
|
Specific target organ toxicity - single exposure |
No data available |
|
Special Remarks on other Toxi Effects on Humans |
Acute Potential Health Effects: Skin: Causes skin irritation. May cause skin sensitization, an allergic reation, which becomes evident upon re-exposure to this material. Eyes: Causes eye irritation. Ingestion: Causes gastrointestinal (digestive) tract irritation with nausea, vomiting, and diarrhea. May be harmful if swallowed. Inhalation: Causes respiratory tract irritation. May cause chemical pneumonitis and pulmonary edema, inflammation, edema of bronchi and larynx. Chronic Potential Health Effects: Repeated or prolonged skin exposure may cause allergic reactions in sensitive individuals. Repeated or prolonged exposure by inhalation may affect respiration and metabolism. |
|
Endocrine disrupting properties |
The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher. RTECS: XR1700000 To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated. |
|
Bioaccumulative potential |
No data available |
|
Persistence and degradability |
No data available |
|
Toxicity to fish |
Static test LC50 - Pimephales promelas (fathead minnow) - 77 mg/l - 96 h (OECD Test Guideline 203) |
|
Toxicity to daphnia and other aquatic invertebrates |
Static test EC50 - Daphnia magna (Water flea) - 57 mg/l - 48 h (OECD Test Guideline 202) |
|
Toxicity to algae |
NOEC - Selenastrum capricornutum (green algae) - 117 mg/l - 4 Days Remarks: (ECHA) |
|
Toxicity to bacteria |
EC50 - activated sludge - > 261 mg/l - 30 min Remarks: (ECHA) |
|
Mobility in soil |
No Information available |
|
Results of PBT and vPvB assessment |
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher. |
|
Endocrine disrupting properties |
The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher. |
|
Other adverse effects |
No data available |
|
Disposal methods |
The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems. |
|
Contaminated packaging |
Dispose of as unused product. |
|
Waste treatment Method |
No data available |
|
UN number |
ADR/RID: 2878 IMDG: 2878 IATA: 2878 |
|
UN proper shipping name |
ADR/RID: Titanium sponge powders IMDG: Titanium sponge powders IATA: Titanium sponge powders |
|
Transport hazard class(es) |
ADR/RID: 4.1 IMDG: 4.1 IATA: 4.1 |
|
Packaging group |
ADR/RID: III IMDG: III IATA: III |
|
Environmental hazards |
ADR/RID: yes IMDG: yes IATA: NO |
|
Further information |
No data available |
|
Safety, health and environmental regulations/legislation specific for the substance or mixture |
This material safety data sheet complies with the requirements of Regulation (EC) No. 1907/2006. |
|
Other regulations |
Take note of Dir 94/33/EC on the protection of young people at work. |
|
Chemical Safety Assessment |
For this product a chemical safety assessment was not carried out |
|
Other Information |
The information above is believed to be accurate and represents the best information currently available to us. However, we make no warranty of merchantability or any other warranty, express or implied, with respect to such information, and weassume no liability resulting from its use. Users should make their own investigations to determine the suitability of the information for their particular purposes. In no event shall be liable for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental, consequential or exemplary damages, howsoever arising, even if Rx Marine International has been advised of the possibility of such damages.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
|
