Buffer Cleaner
Oman Chemical is leading one Largest Supplier, Manufacture a
RXSOL-22-2202-025 turned this vulnerability into an opportunity. "Back-Set" safely removes hardened concrete from a variety of difficult to clean surfaces. It break down the ionic bond in portland cement, releasing the cement from any surface to which it has adhered.
This liquid mixture specifically designed to deal with hard cases of cement cargo deposits or dry cement stains. Its proven advantage is the provision of immediate penetration and complete dissolution of cement, the result being a thorough cleaning.
Chemically Back-Set converts the positive ions in the hardened matrix into negative ions, which dissolves the cement into mud that can be rinsed away. Because it works chemically, rather than mechanically, Back-Set may be used to remove cured concrete, mortar, grout, and stucco from virtually any surface without harm.
ACTIVE MATTER : 98-100 %
WHY RXSOL-22-2202 is better ?
Biodegradable & non flammable , Economical very cost effective
Non-hazardous
Non-fuming
Safe for paint, chrome, aluminum, glass, rubber, plastic, brass & stainless
Dissolves cured cement, concrete, mortar, grout, stucco
Cleans aluminum
Also comes with a foaming spray nozzle
Will not remove rubberized cement
Suitable for the removal of cement deposits and dry stains.
Due to its higher concentration its chemical reaction is very fast.
It's chemical combination meet the requirements of paragraph 1.8.2 of the P&A Standards.
Cement Remover cum cleaner plays an important role to clean cement without scrubbing, which is resulting and damaging the smooth surface. Its simple application method also helps to save manpower. Youtube cement remover video available with this link https://www.youtube.com/watch?v=GJzrh60-q5w
RXSOL-16-1077-020 must be used in open or sufficiently ventilated areas. RXSOL-16-1077-020 should always be used concentrate (without mixing with other solvent.) For best results apply with either by brush, swab, or as a fine spray using suitable hand held spray equipment. Small components may be cleaned by brief immersion in a bath of RXSOL-16-1077-020. Never use RXSOL-16-1077-020 on a running generator or motor. RXSOL-16-1077-020 can be used to clean virtually all electrical equipment & components although is it possible it may affect some types of rubber & plastic . Either remove rubber & plastic parts from component or test on small area for any reaction before cleaning.
RXSOL-25-1005-025 Wax Based Heavy Duty Corrosion Protection Coating Lubrication and Demoulding Cleaning of Injection Mold thimble and Mold Rust Prevention.
Physical Properties:
Melting point | 2450°C |
Boiling Point | 3500°C |
Density | 2.51 g/mL at 25 °C (lit.) |
Solublity | insoluble in H2O, acid solutions |
Form | Powder |
Colour | Black |
Specific gravity | 2.51 |
Resistivity | 4500 (ρ/μΩ.cm) |
Water solublity | Insoluble in water |
Stability | Stable. Incompatible with oxidizing agents. Not flammable. |
insoluble in H2O, acid solutions |
insoluble in H2O, acid solutions |
RXSOL Boat Hull Cleaner strength resulting one step cleaning either its Gel Formula can be brush on or its liquid formula can be sprayed off on the entire boat or Hull area to remove sea growth and lime deposits. Its balance acidic formula immediately starts its function and Safe on aluminium boats and pontoons; Biodegradable, Non-flammable.
Appearance | Clear liquid |
Color | Colorless |
Odor | Odorless |
Initial Boiling Point | <240oC |
Final Boiling Point | >262oC |
Flash Point | 85oC |
Autoignition Temperature | >220oC |
Lower Explosion Limit (vol %) | <0.6% (v/v) |
Upper Explosion Limit (vol %) | >5.5% (v/v) |
Vapour Pressure | <0.0003 kPa at 20oC |
Relative vapor density (air= 1) | <0.01 |
Aromatics | < 0.4% |
Specific Gravity (gr/cm3) | 0.81 at 200C |
Solubility | Soluble |
pH (in 1% dispersion) | 7 |
Pour point (at 0°C) | - 30 |
Viscosity (at 0°C) (cSt) | 3 |
TECHNICAL PROPERTIES:
Composition: Liquid
Appearance: Clear Colorless to charasteristic
Recommended Concentrations: 50-100% by volume
Recommended Temperatures: Ambient
The use of Disodium phosphate treatment in BOILER converts calcium hardness into soft, non-adherent sludge that is easily removed by blowdown.
Sampling And Testing
A sample of boiler water should be drawn for analysis daily. The sample should always be taken from the same point after blow down, cooled and tested immediately. Follow the Rxsol Hardness Test Kit instructions and fill the Boiler Water Log Form according to result results. It is important that regular testing is carried out to ensure levels of treatment are correct.
Physical Properties :
Appearance :White powder
Corrosive action :NonE
pH 1% solution :8.8
Flash point :None
Phosphate/pH relationship recommended to control boiler corrosion. Different forms of phosphate consume or add caustic as the phosphate shifts to the proper form. For example, addition of monosodium phosphate consumes caustic as it reacts with caustic to form disodium phosphate in the boiler water according to the following reaction:
NaH2PO4 | + | NaOH | ® | Na2HPO4 | + | H2O |
monosodium phosphate | sodium hydroxide | disodium phosphate | water |
Conversely, addition of trisodium phosphate adds caustic, increasing boiler water pH:
Na3PO4 | + | H2O | ® | Na2HPO4 | + | NaOH |
trisodium phosphate | water | disodium phosphate |
sodium hydroxide |
The products that we manufacture and supply are as per the following standards:
Distilled Water, Battery Distilled Water, Windshield Wiper Fluid, Distilled Water For Home, Industrial Water, SPA & Saloon Distilled Water, Radiator Coolant Water, Laboratory Water, Medicated Water, Aquarium Water and Saloon Distilled Water.