FIRE PROTECTION
- Part number
- RXSOL-64-2614-001
- Category
- Safety Item
- Brand
- RXSOL
Overview
FIRE SAFETY EQUIPMENT
Safety and SDS
Read the safety data sheet before handling. Wear suitable gloves and eye protection.
View safety data sheet
http://www.ostrem.com/msds/English/S762%20MSDS.pdf
| Product Name | RXSOL-51-6004-025 |
| Product Type | No. 10 Boiler Compound |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| rxsolchemicals@gmail.com |
| INGREDIENT | %W/W | CAS number |
| ethylene glycol | 15-40 | 107-21-1 |
| sodium hydroxide (50%) | 10-30 | 1310-73-2 |
| methanol | 7-13 | 67-56-1 |
| methylene phosphonic acid | 1-5 | 6419-19-8 |
| tetrasodium salt of ethylene diamine tetraacetic acid (EDTA) | 5-10 | 64-02-8 |
Corrosive liquid. Causes burns. Harmful if swallowed. Combustible liquid.
|
Inhalation |
Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention. |
|
Ingestion |
Induce vomiting only on the direct advice of a poison control centre. Drink 1-2 glasses of water. Never give anything by mouth to an unconscious person. Get medical attention. |
|
Eye contact |
Flush with plenty of water for at least 15 minutes. Get medical attention. |
|
Skin contact |
Remove contaminated clothing and flush with plenty of water. |
| Flash point (test method) | 39C(TCC) |
| Flammable limits (%) | Not applicable |
| Lower | Not applicable. |
| Upper | Not applicable |
| Fire extinguishing substances | Use dry chemicals, carbon dioxide, water spray or foam. |
| Autoignition temperatures | Not applicable |
| Hazardous combustion products | May liberate carbon monoxide, carbon dioxide and Sulphur dioxide. |
| Explosion data | |
| Sensitivity to mechanical impact | Not applicable |
| Sensitivity to static discharge | Not applicable |
| Special firefighting procedures | As for surrounding fire. |
|
Personal precautions |
Wear appropriate protective equipment. |
|
Environmental precautions |
Prevent from entering sewers, waterways or low areas. |
|
Methods for cleaning up |
Isolate hazard area and restrict access. Small spills: soak up with inert absorbent material and scoop into containers. Large spills: prevent contamination of waterways. Dike and pump into suitable containers. Clean up residual with absorbent material, place in appropriate container and flush with water. |
|
Handling |
Do not ingest. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. |
| Storage | Keep out of reach of children. Keep container tightly closed. Store in a cool, dry area. |
|
Engineering controls |
Provide exhaust ventilation to keep airborne levels below recommended exposure limits. |
| Respiratory protection | Not normally necessary. An N95 NIOSH respirator may be worn. |
| Eye protection | Chemical goggles. Wear a face shield if splashing hazards exists. |
| Other protection | Not normally necessary. |
Exposure limits:
| INGREDIENT | ACGIH | OSHA | Other |
| ethylene glycol | TLV CEIL: 100mg/m3 8 hours | ||
| sodium hydroxide (50%) | 2 mg/m3 Ceil. | ||
| methanol | CAD AB OEL 200 ppm (262mg/m3) | ||
| methylene phosphonic acid | Not available | ||
| tetrasodium salt of ethylene diamine tetraacetic acid (EDTA) | Not available |
| Physical state | Liquid |
| Solubility in water | Complete |
| Boiling point | Not available |
| Vapour pressure | Not available |
| Vapour density | Not available |
| Evaporation rate | Not available |
| Freezing point | -45C |
| Odour threshold | Not available |
| Sp. Gravity | 1.176 |
| pH | 1% Solution: 12.4 |
| Appearance & odour | Clear, colourless liquid with slight ammonia odour |
|
STABILITY |
Stable |
|
Conditions of instability |
Not available |
|
Incompatibility |
( ) Water (X) Oxidizers (X) Acid (X) Base (X) Other: chlorinated hydrocarbons, aluminum, tin, lead, zinc, copper. |
|
Conditions of reactivity |
Not available |
|
Hazardous decomposition products |
Not available |
| POTENTIAL ACUTE HEALTH EFFECTS | |
| Inhalation | Corrosive to respiratory system. |
| Ingestion | Harmful if swallowed. Causes burns to mouth, throat and stomach. |
| Eye contact | Causes burns. |
| Skin contact | Causes burns. |
| Skin absorption | Not available |
| POTENTIAL CHRONIC HEALTH EFFECTS | |
| Inhalation | Repeat or prolonged exposure may cause damage to lungs. |
| Ingestion | Not available |
| Eye contact | Not available |
| Skin contact | Not applicable |
| Skin absorption | Not applicable |
| Irritancy of product | See WHMIS criteria |
| Sensitization of product | Not available |
| Carcinogenicity: | |
| IARC (1, 2A or 2B) | No known significant effects. |
| ACGIH: (A1, A2 or A3) | No known significant effects. |
| Reproductive toxicity | No known significant effects. |
| Teratogenicity | No known significant effects. |
| Mutagenicity | No known significant effects. |
| Synergistic product | Not available |
|
HAZARDOUS INGREDIENTS |
CAS NO |
TOXICITY DATA |
|
ethylene glycol |
107-21-1 |
LD50 oral rat: 4700 mg/kg LD50 dermal rabbit: 9530 mg/kg |
| sodium hydroxide (50%) | 1310-73-2 | LD50 oral (rabbit) 365 mg/kg |
| methanol | 67-56-1 |
LDL0 oral human: 300 mg/kg LD50 oral rabbit: 12,800 mg/kg LC50 inhalation rat: 64,000 ppm/4H |
| methylene phosphonic acid | 6419-19-8 |
LD50 Oral (rat) 2910 mg/kg LD50 Dermal (rabbit) >6310 mg/kg |
| tetrasodium salt of ethylene diamine tetraacetic acid (EDTA) | 64-02-8 |
LD50 Oral (rat) >2000 mg/kg LD50 Dermal (rabbit) 1350 mg/kg |
| Ecotoxicological information | Not available |
| Other information |
|
Waste disposal |
Disposal of all waste must be done according to local, provincial and federal regulations. |
|
TDG classification |
CORROSIVE LIQUID, FLAMMABLE, N.O.S. (SODIUM HYDROXIDE, METHANOL); Class 8 (3); UN 2920; PG II |
|
WHMIS |
E | Corrosive Material |
| B3 | Combustible Material | |
| D2A | Material Causing Other Toxic Effects |
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all the information required by the CPR.
The information contained in this safety data sheet is given in good faith. It is accurate to the best of our knowledge and belief and represents the most up to date information. The information given in this data sheet does not constitute or replace the users own assessment of workplace risk as required by other health and safety legislation.
---------------------------------------------------------------------------------------------------------------------------------------------------
http://www.ostrem.com/msds/English/S772%20MSDS.pdf
| Product Name | RXSOL-51-6004-025 |
| Product Type | PBT-20 Polymer Boiler Treatment |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| rxsolchemicals@gmail.com |
| INGREDIENT | %W/W | CAS number |
| Polyacrylic Acid Sodium Salt | 15-40 | Not available |
Eye irritant. Harmful if swallowed.
|
Inhalation |
Remove from exposure. Get fresh air. |
|
Ingestion |
Do not induce vomiting. If irritation persists, seek medical attention. |
|
Eye contact |
Flush with plenty of water for 15 minutes. Get medical attention if irritation persists. |
|
Skin contact |
Remove contaminated clothing and flush with plenty of water. |
| Flash point (test method) | Not applicable |
| Flammable limits (%) | Non-flammable |
| Lower | Not applicable. |
| Upper | Not applicable |
| Fire extinguishing substances | Use dry chemicals, carbon dioxide, water spray or foam. |
| Autoignition temperatures | Not applicable |
| Hazardous combustion products | May liberate carbon monoxide, carbon dioxide and Sulphur dioxide. |
| Explosion data | |
| Sensitivity to mechanical impact | Not applicable |
| Sensitivity to static discharge | Not applicable |
| Special firefighting procedures | As for surrounding fire. |
|
Personal precautions |
Wear appropriate protective equipment. |
|
Environmental precautions |
Prevent from entering sewers, waterways or low areas. |
|
Methods for cleaning up |
Isolate hazard area and restrict access. Small spills: soak up with inert absorbent material and scoop into containers. Large spills: prevent contamination of waterways. Dike and pump into suitable containers. Clean up residual with absorbent material, place in appropriate container and flush with water. |
|
Handling |
Do not ingest. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. |
| Storage | Keep out of reach of children. Keep container tightly closed. Store in a cool, dry area. |
|
Engineering controls |
Special ventilation requirements not normally necessary |
| Respiratory protection | Not normally necessary. |
| Eye protection | Not normally necessary. Safety glasses may be worn. |
| Other protection | Not normally necessary. |
Exposure limits:
| INGREDIENT | ACGIH | OSHA | Other |
| polyacrylic sodium salt | Not applicable |
| Physical state | Liquid |
| Solubility in water | Complete |
| Boiling point | Not available |
| Vapour pressure | Not available |
| Vapour density | Not available |
| Evaporation rate | Not available |
| Freezing point | 0C |
| Odour threshold | Not available |
| Sp. Gravity | 1.12 |
| pH | 8-8.5 |
| Appearance & odour | light brown liquid with a slight odour |
|
STABILITY |
Stable |
|
Conditions of instability |
Not available |
|
Incompatibility |
( ) Water (X) Oxidizers ( ) Acid ( ) Base ( ) Other |
|
Conditions of reactivity |
Not available |
|
Hazardous decomposition products |
Not available |
| POTENTIAL ACUTE HEALTH EFFECTS | |
| Inhalation | No known significant effects |
| Ingestion | No known significant effects |
| Eye contact | May cause temporary discomfort and redness |
| Skin contact | May cause temporary discomfort |
| Skin absorption | Not available |
| POTENTIAL CHRONIC HEALTH EFFECTS | |
| Inhalation | No known significant effects |
| Ingestion | Not available |
| Eye contact | Not available |
| Skin contact | Prolonged contact may cause discomfort |
| Skin absorption | Not applicable |
| Irritancy of product | See WHMIS criteria |
| Sensitization of product | Not available |
| Carcinogenicity: | |
| IARC (1, 2A or 2B) | No known significant effects. |
| ACGIH: (A1, A2 or A3) | No known significant effects. |
| Reproductive toxicity | No known significant effects. |
| Teratogenicity | No known significant effects. |
| Mutagenicity | No known significant effects. |
| Synergistic product | Not available |
|
HAZARDOUS INGREDIENTS |
CAS NO |
TOXICITY DATA |
| None |
| Ecotoxicological information | Not available |
| Other information |
|
Waste disposal |
Disposal of all waste must be done according to local, provincial and federal regulations. |
|
TDG classification |
Not Regulated |
|
WHMIS |
D2B | Material Causing Other Toxic Effects |
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all the information required by the CPR.
The information contained in this safety data sheet is given in good faith. It is accurate to the best of our knowledge and belief and represents the most up to date information. The information given in this data sheet does not constitute or replace the users own assessment of workplace risk as required by other health and safety legislation.
---------------------------------------------------------------------------------------------------------------------------------------------------
http://www.ostrem.com/msds/English/S768%20MSDS.pdf
| Product Name | RXSOL-51-6004-025 |
| Product Type | E-40 Boiler Water Blend |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| rxsolchemicals@gmail.com |
| INGREDIENT | %W/W | CAS number |
| tetrasodium salt of ethylene diamine tetraacetic acid (EDTA) | 60-100 | 64-02-8 |
Corrosive liquid. Causes burns. Harmful if swallowed.
|
Inhalation |
Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention. |
|
Ingestion |
Induce vomiting only on the direct advice of a poison control centre. Get medical attention. |
|
Eye contact |
Flush with plenty of water for at least 15 minutes. Get medical attention. |
|
Skin contact |
Remove contaminated clothing and flush with plenty of water. |
| Flash point (test method) | Not applicable |
| Flammable limits (%) | Non-flammable |
| Lower | Not applicable. |
| Upper | Not applicable |
| Fire extinguishing substances | Use extinguishing media appropriate for surrounding fire. |
| Autoignition temperatures | Not applicable |
| Hazardous combustion products | May liberate carbon oxides and nitrogen oxides. |
| Explosion data | |
| Sensitivity to mechanical impact | Not applicable |
| Sensitivity to static discharge | Not applicable |
| Special firefighting procedures |
As for surrounding fire. Fire fighters should wear full protective clothing and self contained breathing equipment. |
|
Personal precautions |
Wear appropriate protective equipment. |
|
Environmental precautions |
Prevent from entering sewers, waterways or low areas. |
|
Methods for cleaning up |
Isolate hazard area and restrict access. Small spills: soak up with inert absorbent material and scoop into containers. Large spills: prevent contamination of waterways. Dike and pump into suitable containers. Clean up residual with absorbent material, place in appropriate container and flush with water. |
|
Handling |
Do not ingest. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. |
| Storage | Keep out of reach of children. Keep container tightly closed. Store in a cool, dry area. |
|
Engineering controls |
Provide exhaust ventilation to keep airborne levels below recommended exposure limits. |
| Respiratory protection | If exposure exceeds occupational exposure limits, use an appropriate NIOSH approved respirator |
| Eye protection | Chemical goggles. Wear a face shield if splashing hazards exists. |
| Other protection | Wear protective clothing as necessary to prevent skin contact. |
Exposure limits:
| INGREDIENT | ACGIH | OSHA | Other |
|
Tetrasodium salt of ethylene diamine tetraacetic acid (EDTA) |
Not available |
| Physical state | Liquid |
| Solubility in water | Complete |
| Boiling point | 100C |
| Vapour pressure | Not available |
| Vapour density | Not available |
| Evaporation rate | Not available |
| Freezing point | Not available |
| Odour threshold | Not available |
| Sp. Gravity | 1.3 |
| pH | 1% Solution: 13.5 |
| Appearance & odour | clear pale solution |
|
STABILITY |
Stable |
|
Conditions of instability |
Not available |
|
Incompatibility |
( ) Water (X) Oxidizers ( ) Acid ( ) Base ( ) Other |
|
Conditions of reactivity |
Not available |
|
Hazardous decomposition products |
produces hydrogen in the presence of aluminum. |
| POTENTIAL ACUTE HEALTH EFFECTS | |
| Inhalation | Irritating to respiratory system. |
| Ingestion | May be harmful if swallowed. |
| Eye contact |
May cause mild to severe irritation such as stinging, tearing, redness and swelling of the eyes. |
| Skin contact | May cause skin irritation. |
| Skin absorption | Not available |
| POTENTIAL CHRONIC HEALTH EFFECTS | |
| Inhalation | Repeat or prolonged exposure may cause damage to lungs. |
| Ingestion | Not available |
| Eye contact | Not available |
| Skin contact | Not available |
| Skin absorption | Not available |
| Irritancy of product | See WHMIS criteria |
| Sensitization of product | Not available |
| Carcinogenicity: | |
| IARC (1, 2A or 2B) | No known significant effects. |
| ACGIH: (A1, A2 or A3) | No known significant effects. |
| Reproductive toxicity | No known significant effects. |
| Teratogenicity | No known significant effects. |
| Mutagenicity | No known significant effects. |
| Synergistic product | Not available |
|
HAZARDOUS INGREDIENTS |
CAS NO |
TOXICITY DATA |
| tetrasodium salt of ethylene diamine tetraacetic acid (EDTA) | 64-02-8 |
LD50 Oral (rat) >2000 mg/kg LD50 Dermal (rabbit) 1350 mg/kg |
| Ecotoxicological information | Not available |
| Other information |
|
Waste disposal |
Disposal of all waste must be done according to local, provincial and federal regulations. |
|
TDG classification |
CORROSIVE LIQUID, N.O.S. (TETRASODIUM EDTA SOLUTION); Class 8; UN 1760; PG III |
|
WHMIS |
E | Corrosive |
| D2B | Other toxic effects |
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all the information required by the CPR.
The information contained in this safety data sheet is given in good faith. It is accurate to the best of our knowledge and belief and represents the most up to date information. The information given in this data sheet does not constitute or replace the users own assessment of workplace risk as required by other health and safety legislation.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
