Your shopping cart is empty.
Product Code: RXSOL-21-2124-010
Product Code: RXSOL-21-2128-100
Product Code: RXSOL-20-2006-210
For light contamination dilute with water in the ratio 1:20 . For medium contamination dilute with a petrosolvent. And for heavy contamination concentrated RXSOL-20-2006-0210 is suggested.
For Engine Room & Cargo Tank Cleaner
Dosage:- Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended where as medium contamination dilution with Petro solvent , And for heavy contamination neat RXSOL CB 2006 is suggested to use.
Procedure of use :- RXSOL-20-2006-025 is recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. It may be applied by brush, spray, immersion, soaking, or any other conventional means.RXSOL-20-2006-025 is used neat. Allow a residence time of at least 20- 45 minutes where possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed to separate in a holding tank for atleast 3-5 hours before passing through an oily water separator.
Tank Cleaning after Mineral Oils/ Lube Oils / Slope-Black Oil
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a temperature between 65°C & 80°C then stripped constantly and transferred to a holding tank for separation.The time for this will vary depending on amount of RXSOL-20-2006-025 used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-2006-025 on tank surfaces to be cleaned, left for at least 30 minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.
Product Code: RXSOL-20-3004-025
Product Code: RXSOL-70-7003-020
Product Code: RXSOL-16-1094-025
Product Code: RXSOL-15-1106-001
Product Code: RXSOL-15-3007-001
TWO WAYS TO SPARKLING DISHES
* For tough grease, pour just one drop of RXSOL Dish Wash is a ideal solution on scrub or sponge and apply on the utensil.
* For regular cleaning, dilute a few drop of RXSOL Dish Wash in a bowl of water.
* Dip the scrub or sponge in the solution and use. For re-use, just dampen the sponge and use when required.
* Washing with RXSOL leaves on scratches or residue on utensils.
Great Offers and Discounts on RXSOL dishwashing soap and dish soap detergent which is helpfull for dishwashing. Main characteristic of natural and environmentally friendly RXSOL Gel Dishwashing Liquid detergent soap was very good and tough on grease and baked food and very gentle on your hands & leaves your dishes with a clean, streak-free shine.
RXSOL is ideal for stainless steel, crockery, cutlery and non-stick cookware. RXSOL dish wash gives double power of lime and vinegar where Lime cleans out the toughest grease and burnt stains while vinegar removes residual food. As a result, you have sparkling dishes that are completely clean.
Enjoy lemon washing at 50% discount with double power of lime and vinegar. We have good plan for distributorship. Refer this link http://rxmarine.com/dish-wash-distributorship-offer
Product Code: RXSOL-20-2401-210
| PROBLEM | CLEARING AGENT | COMMENTS |
| Rust and other corrosion products. Embedded or adhering "free iron | Very light rust stain can be removed by 10% nitric acid. More significant rust or embedded iron will require picking. See also previous sections on Passivating and Picking. Sand or glass-bead blasting is another option | Wear PPE as appropriate. Afterwards rinse well with clean water. Mix in acid-proof container, and be very careful with the acid, (See Precautions for acid cleaners) |
| Routine cleaning of boat fittings. | Frequent washing down with fresh water. | Recommended after each time the boat is used in salt water. |
| Cooking pot boiled dry. | Remove burnt food by soaking in hot water with detergent, baking soda or amonia. | Afterwards clean and polish. with a mild abrasive if necessary. See comments re steel wool. |
| Dark oxide from welding or heat treatment. | "Picking Paste" or picking solutions given on previous page. | Must be careful rinsed, and use care in handling (see Precautions for acid cleaners). |
| Scratches on polished (satin or brushed) finish. | Slight scratches - use impregnated nylon pads. Polish with polishing wheel dressed with iron-free abrasive for deeper scratches. Follow polish lines. Then clean with soap or detergent as for routine cleaning | Do not use ordinary steel wool - iron particles can become embedded in stainless steel and cause further surface problems. Stainless steel and "Scotchbrite" scouring pads are satisfactory. |
| PROBLEM | CLEARING AGENT | COMMENTS |
| Routine cleaning All finishes | Soap mild detergent and water. (preferably warm) | Sponge, rinse with clean water, wipe dry if necessary. Follow polish lines. |
| Fingerprints All finishes | Soap warm water or organic solvent (eg acetone, alchol, methylated spirits) | Rinse with clean water and pipe dry. Follow polish lines. |
| Stubborn stains and discoloration. All finishes. | Mild cleaning solutions. Ensure any properietary cleaners state compatibility with stainless steel. Phpsphoric acid cleaners may also be effective | Use rag, sponge or fibre brush (soft nylon or natural bristle. An old toothbrush can be useful). Rinse well with clean water and wipe dry. Follow polish lines. |
| Lime deposits from hard water. | Solution of one part vinegar to three parts water. | Soak in solution then brush to loosen. Rise well with clean water. |
| Oil or grease marks. All finishes. | Organic solvents (eg. acetone, alchol, methylated spirits, proprietary "safety solvents"). Baked-on grease can be softened beforehand with ammonia |
Clean after with soap and water, rinse with clean water and dry. Follow polish lines |
| PROBLEM | CLEARING AGENT | COMMENTS |
| Rust and other corrosion products. Embedded or adhering "free iron | Very light rust stain can be removed by 10% nitric acid. More significant rust or embedded iron will require picking. See also previous sections on Passivating and Picking. Sand or glass-bead blasting is another option | Wear PPE as appropriate. Afterwards rinse well with clean water. Mix in acid-proof container, and be very careful with the acid, (See Precautions for acid cleaners) |
| Routine cleaning of boat fittings. | Frequent washing down with fresh water. | Recommended after each time the boat is used in salt water. |
| Cooking pot boiled dry. | Remove burnt food by soaking in hot water with detergent, baking soda or amonia. | Afterwards clean and polish. with a mild abrasive if necessary. See comments re steel wool. |
| Dark oxide from welding or heat treatment. | "Picking Paste" or picking solutions given on previous page. | Must be careful rinsed, and use care in handling (see Precautions for acid cleaners). |
| Scratches on polished (satin or brushed) finish. | Slight scratches - use impregnated nylon pads. Polish with polishing wheel dressed with iron-free abrasive for deeper scratches. Follow polish lines. Then clean with soap or detergent as for routine cleaning | Do not use ordinary steel wool - iron particles can become embedded in stainless steel and cause further surface problems. Stainless steel and "Scotchbrite" scouring pads are satisfactory. |
| PROBLEM | CLEARING AGENT | COMMENTS |
| Routine cleaning All finishes | Soap mild detergent and water. (preferably warm) | Sponge, rinse with clean water, wipe dry if necessary. Follow polish lines. |
| Fingerprints All finishes | Soap warm water or organic solvent (eg acetone, alchol, methylated spirits) | Rinse with clean water and pipe dry. Follow polish lines. |
| Stubborn stains and discoloration. All finishes. | Mild cleaning solutions. Ensure any properietary cleaners state compatibility with stainless steel. Phpsphoric acid cleaners may also be effective | Use rag, sponge or fibre brush (soft nylon or natural bristle. An old toothbrush can be useful). Rinse well with clean water and wipe dry. Follow polish lines. |
| Lime deposits from hard water. | Solution of one part vinegar to three parts water. | Soak in solution then brush to loosen. Rise well with clean water. |
| Oil or grease marks. All finishes. | Organic solvents (eg. acetone, alchol, methylated spirits, proprietary "safety solvents"). Baked-on grease can be softened beforehand with ammonia |
Clean after with soap and water, rinse with clean water and dry. Follow polish lines |
DENGEROUS FOR ALL BODY PART
NB. Before disposing the passivating fluid it should be neutralized. ( Caustic / Soda ash / slaked lime )
In accordance with the latest E.E.C Council directives
R 34 : Causes burn
S2 : Keep out of reach of children
S 26 : In case of contact with eyes rinse immediately with plenty of wate and seek medical advice
Product Code: RXSOL-40-4008-020
Appearance: Clear, Colorless liquid
Physical State: Liquid
Color: Colorless
Odor: Characteristic Odor
Odor threshold Not applicable
pH <= 3.7
Melting point/freezing point -22 °C
Boiling Point/Range 105 °C
Flash point Not flammable
Evaporation Rate No information available
Flammability (solid, gas) Not flammable
Flammability Limit in Air Not applicable
Upper flammability limit:
Lower flammability limit:
Vapor pressure 26 mm Hg @ 30 °C
Vapor density No information available
Density 1.10 g/cm³ @ 20ºC
Specific gravity 1.10
Water solubility completely soluble
Solubility in other solvents No information available
Partition coefficient log Kow = -1.5 @ 20 °C
Autoignition temperature Not combustible
Decomposition temperature 100 °C
Viscosity, kinematic 1.06 cP @ 20 °C
Viscosity, dynamic No information available
Explosive properties No information available
Oxidizing properties Strong oxidizer
Molecular weight 34
Bulk density Not applicable
Product Code: RXSOL-10-2010-210
Product Code: RXSOL-16-1093-025
| Product Properties | ||
| Appearance | Clear Colourless Liquid | Vapor Density : Heavier than air |
| Flash Point | 63°C (Closed Cup) | Stabilit Very stable understandard normal conditions |
| Compatibility | ||
|
Metal |
No known effect |
Note: After use the product must always be well sealed in the drum. |
| Packaging | Order No | Size (in kgs./lts.) |
| RXSOL-16-1093-025 | 7/25 Lts | |
