Your shopping cart is empty.
Product Code: RXSOL-19-3356-070
Product Code: RXSOL-62-4444-455
TEchnical Speciafication
Remark
Product Code: RXSOL-43-8936-025
Biocide : Isothiazolinone bactericide:
CMIT/MIT-14 active
content 14% ,
density 1.30g/cm3,
pH(1% water solution) 2.0-4.0,
used for reverse osmosis water treatment
Product Code: RXSOL-62-4444-4555
TEchnical Speciafication
Remark
Product Code: RXSOL-22-2202-220
ACTIVE MATTER : 98-100 %
WHY RXSOL-22-2202 is better ?
Biodegradable & non flammable , Economical very cost effective
Non-hazardous
Non-fuming
Safe for paint, chrome, aluminum, glass, rubber, plastic, brass & stainless
Dissolves cured cement, concrete, mortar, grout, stucco
Cleans aluminum
Also comes with a foaming spray nozzle
Will not remove rubberized cement
Suitable for the removal of cement deposits and dry stains.
Due to its higher concentration its chemical reaction is very fast.
It's chemical combination meet the requirements of paragraph 1.8.2 of the P&A Standards.
Excellent , concentrated and very effective cement remover with powerfull dissolving properties used on cement and bulk carriers.
The hardened concrete is saturated with Back-Set, either with a brush or by spraying. After 15-20 minutes, the area is again saturated with the chemical. The concrete typically begins to soften in 20-30 minutes,and can be rinsed off with water.The amount required for dosage can be obtained BY knowing the deposition composition as well as nature of cement to be removed.5 to 20 % recommended .These are recommended values based on experience. For optimum results dose RXSOL-22-2202-025 directly to the surface .
The amount required for dosage can be obtained BY knowing the deposition composition as well as nature of CEMENT to be removed . 5 to 20 % recommended .These are recommended values based on experience.
For optimum results dose RXSOL-22-2202-025 directly to the surface
Undiluted : In cases where we deal with heavy deposit build–up, CEMENT REMOVER must be applied undiluted.
Diluted : In cases of light deposition, on large surface areas, a solution between 10–40% may be used.
METHOD :::
1.For heavy deposition and thick layers of cement, a concentrated and stronger cleaner will be necessary to cut through the layers of cement.
2.Use a scraper, metal scrubber or flat head screwdriver to remove as much of the cement as possible.
3.For the remaining cement, apply this chemical
4.Once the cement loosens, scrub the area with a scrubber until it is all removed from the surface.
5.Rinse the area well with clean water.
6.Clean the area with alkaline soap and water
7.Flush system completely.
It is highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver as an alternative to using hazardous acids for concrete removal. Back-Set is a one-of-a-kind formula. It uses an active ingredient found in sugar cane syrup, and is completely biodegradable.
RXSOL-22-2202-025 turned this vulnerability into an opportunity. "Back-Set" safely removes hardened concrete from a variety of difficult to clean surfaces. It break down the ionic bond in portland cement, releasing the cement from any surface to which it has adhered.
Product Code: RXSOL-22-1495-040
Product Code: RXSOL-22-2164-001
Product Code: RXSOL-25-4053-005
Physical Properties
| Appearance | : Clear Liquid |
| Colour | : Straw |
| Density | : 0.80 g/ml @ 20 °C. |
| Flash point | : 38°C minimum |
| Coverage Area |
: 20 - 25 m²/litre Approx |
Product Code: RXSOL-25-1011-010
Product Code: RXSOL-19-2043-190
Product Code: RXSOL-94-1438-025
Cyanopyridines White Crystaline Solid.
Product Code: RXSOL-19-1215-027
| PRODUCT NAME | : | ACETONECYANOHYDRIN |
| CAS number | : | 75-86-5 |
| UN number | : | 1541 |
| Formula | : | (CH3)2COHON |
| Odour | : | |
| Solubility in water | : | COMPLETE |
| Density | : | 0.932 at 19 oC |
| Boiling point | : | 95 oC |
| Melting point | : | 20 oC |
| Viscosity | : | |
| Flashpoint | : | 74 oC |
| Explosive limits | : | 2 – 11 Vol % |
| Vapour pressure | : | 1.1 mbar at 20 oC |
| Skin absorption/irriation | : | YES |
| TLV Country | : | |
| Pollution category 1994 | : | A |
